Jump to content
SAU Community

Recommended Posts

factory stats at the flywheel for the different models are below, it's hard to gauge power at the wheels, cause every dyno will read sligthly different

R32 RB25DE 132kw

R33 RB25DE non type-s 140kw

R33 RB25DE type-s 147kw

R43 RB25DE 147kw

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-1481865
Share on other sites

factory stats at the flywheel for the different models are below, it's hard to gauge power at the wheels, cause every dyno will read sligthly different

R32  RB25DE 132kw

R33  RB25DE non type-s   140kw  

R33  RB25DE type-s  147kw

R43  RB25DE 147kw

i remember hi performance imports magazine dynoed a rb25de , they eventually got it up to around 120 kw@ rw , mainly by playing with the ignition timing ( advanced few degrees ) improving air inlet and some other tricks . must find that magazine and be a bit more specific .

by the way whats the difference between non type s and type s ?

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-1484004
Share on other sites

i remember hi performance imports magazine dynoed a rb25de , they eventually got it up to around 120 kw@ rw , mainly by playing with the ignition timing ( advanced few degrees ) improving air inlet and some other tricks . must find that magazine and be a bit more specific .

by the way whats the difference between non type s and type s ?

i read that article too... it was on an series 1 silver sedan.

they advanced timing

fcd

removed standard airbox lid

added a cardboard snorkel

type s has been quoted to have an extra 7kw (and has an exhaust flap on the stock system)

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-1484270
Share on other sites

What sort of power can be achieved with an RB25DE ? Has anyone worked one ?

Have been wanting to change mine to an N/A since I saw a HCR32 modified to fit in an RB25DE ( in the turbo body with brakes etc. ) Yes the car WAS a turbo but had an N/A installed. The RB25DE was very worked but I don't speak Jap so I didn't find out the power output.

I know you think I'm :crazy: but if you could have heard this car go you would cream yourself ( snorting, farting, barking and growling sounds that no turbo car could EVER make !!! ) :wave:

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-1490561
Share on other sites

:werd:

This car I saw in Osaka had open alloy trumpets and you could look down them and SEE the fuel injector spraying !!! It also had extractors into a 2 3/4" system with one muffler, and then dumped out the side. The compression of the engine was so high that the air coming out the exhaust nearly un-tied your shoe laces !! :wave:

I just wish I had done the swap when I blew up my RB20DET. But the only thing that stopped me was the knowledge that I was going to have +200 rwkw. I now have the power but just wish I had the old school noise :kewl:

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-1490716
Share on other sites

So by that rational, it's possible to get good 150+rwkw with cams, injectors, head work etc. ( I suppose with REAL money spent, the number's could be higher ). But I guess it's more about the torque figure and where it all happens in the rev range.

I better start saving real hard :huh:

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-1494214
Share on other sites

  • 8 months later...
This car I saw in Osaka had open alloy trumpets and you could look down them and SEE the fuel injector spraying

by that you mean it had their own individual tb with bell mouths added to it. they make the engine scream and rev really loud haha.

damn its been awhile and i should've kept track of this thread. i totally forgot about it :worship:

R32 RB25DE 132kw

i thought R32's only came in RB20 dude?

i rekon the rb25de would be a good engine to work with. work it off its nuts then slap on a turbo man it would be a monster.

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-2119153
Share on other sites

by that you mean it had their own individual tb with bell mouths added to it. they make the engine scream and rev really loud haha.

damn its been awhile and i should've kept track of this thread. i totally forgot about it :devil:

i thought R32's only came in RB20 dude?

i rekon the rb25de would be a good engine to work with. work it off its nuts then slap on a turbo man it would be a monster.

Yes some R32s came out with a non-turbo RB25DE engine (although less powerful than the R33 version).

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-2122320
Share on other sites

  • 2 weeks later...
Yes some R32s came out with a non-turbo RB25DE engine (although less powerful than the R33 version).

yeh, I have an R32 RB25DE.. any light mods I can do? I'm a student so strapped for cash, but it does have a new air filter, performance clutch and exhaust.. what else could be done?

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-2151289
Share on other sites

  • 2 weeks later...
$300 will get you a set of Coby extractors from NZ. Very good build quality!

He said it already has a performance exhaust on it... so any gain would be minimal (surley).

yeh, I have an R32 RB25DE.. any light mods I can do? I'm a student so strapped for cash, but it does have a new air filter, performance clutch and exhaust.. what else could be done?

Perhaps getting some cams would help... provided you don't mind revs, that is.

Get a job when you finish uni and get a turbo (like I did). Till then, save your money, and enjoy your lightweight NA car

Link to comment
https://www.sau.com.au/forums/topic/81666-rb25de/#findComment-2181670
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...