Jump to content
SAU Community

Recommended Posts

I'm gonna make this short quick and simple!

Just a few years ago, 13 sec passes were considered quick for a street car....

Are 12 second passes now overtaking that? Is a 13 second pass now not good enough?

Just want to get peoples thoughts on this.

Link to comment
https://www.sau.com.au/forums/topic/83058-are-12s-the-new-13s/
Share on other sites

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

13's are quick for a street car. But we are getting faster stock cars, which raises the bar and makes people want to spend a few extra bucks to get into the next bracket to stand out.

A stock GTST for arguments sake runs a 14.5, which compared to a stock 5 litre VS holden 15-16?

So we have a better setup in the suspension department, a driveline thats tough as nails and an engine that responds to modification like no other.

Cheers

Sumo

Best thread this week!

It's gonna be like this for a while to come but eventually, 11's will be it. Speak to the old old OLD Castlereagh boys about street cars racing and tell them your daily driver runs a 13.9 ET and they're usually amazed. You need to remember that 6-pack EH Holdens running 15's were way cool once upon a time.

Add that to the list of 13 sec factory cars coming out that are relatively common on the street, (Falcodores etc) and the bar gets raised that extra little bit.

As far as Skylines are concerned, look at what 20 something people on this forum alone have done with their mostly stock 33's on radials @ WSID and other tracks. 12's are the norm now.

Adrian

Speaking about Skylines only and specifically WSID which i've been attending on a weekly basis since the day it opened.

When it first opened an R33 GTS-T with a std turbo doing a low 13sec pass was quite amazing. Then only a year or so ago a couple of people cracked a 12.9sec with a std turbo. Now their are people doing high 12's with std turbo's which I never thought i'd see.

With modified Skylines a low 12 or high 11sec pass was astonishing. Now fairly standard GTR's are doing low 12's and modified R32/R33 GTR's are doing low-mid 11's without breaking a sweat !

It seems as though these days if you aren't doing a 10 something in a GTR or an 11 something in a GTS-t you just aren't cutting it.

Hopefully i'm back out at WSID before the end of the year doing mid-12's ... which is my goal at this stage.

I think it depends on the car involved. I think a 12 sec street car is fast, although a 13 second street FWD is very fast as they dont have the ET, but the mph. my old MX6 did a 13.7 et, but a 112mph trap speed. My freinds very close to stock GTiR (fuel pump, wound up boost thats it) did a 12.2 et with a mph of 111 trap speed. he also had a 60 foot of 1.6, where mine was 2.5 seconds.

So yes I think alot more cars are running 12s but I think it depends on the drive of the car, RWD, FWD, AWD!

Rhys

Yeah my goal is to cut a 12.4 at least in the next 6 months....

Then take it from there.

But there are alot of quicker factory cars coming out but like people have said back in 00' and 01' a 13 was quick, now its slow.....

My mate has a WRX wagon that does a 12.3 and that thing feels slow! I dunno what is going on these days!

I think it depends what circle you travel in.

I know a number of guys that are worrying about a cage.

A reasonably modded turbo car, but still street, is 11sec or quicker, & beleive me that's heaps cheaper & easier than an 15 sec. EH - & also much nicer to drive on the street.

Regards

Out of interest, my std turbo'd 33 GTS-t went 12.6 @ 107mph last sunday.

Damm, that's good. That mph is especially impressive for the std turbo as well.

Would you mind posting your splits (i.e 60', 330' etc) so I can do a comparison with mine? :)

I managed a 13.1 @ 103mph last Sunday with Std turbo which I was pretty happy with. I think i've still got a bit more improvement left in that time with the current mods once I improve my launches a bit more. I'm planning to go out again in the next couple of weeks and see if I can crack that illusive 12 on the Std turbo.

Damm, that's good. That mph is especially impressive for the std turbo as well.

Would you mind posting your splits (i.e 60', 330' etc) so I can do a comparison with mine? ;)

I managed a 13.1 @ 103mph last Sunday with Std turbo which I was pretty happy with. I think i've still got a bit more improvement left in that time with the current mods once I improve my launches a bit more. I'm planning to go out again in the next couple of weeks and see if I can crack that illusive 12 on the Std turbo.

What was your 60" times? 60 footers are a key to running a 12 with the standard turbo. I ran a 12.98 with a 2.02 60'. If you can get a sub 2.0, you should be home and hosed.

I also believe that it's all down to the people you hang around with, and how quick their cars are. If you're riding in a 11second GTR all day, then of course a 13 second S13 is going to seem slow. But to the general populous who drive Corollas, Astras etc etc ... the 13 second S13 is still damn quick.

What was your 60" times?  60 footers are a key to running a 12 with the standard turbo.  I ran a 12.98 with a 2.02 60'.  If you can get a sub 2.0, you should be home and hosed.

I was doing consistant 1.9 60" time's on all three 13.1 runs that I did on the day.

What mph did you run?

Also, did you shift into 4th before the finish line? I found that I was always just about on the rev limit just before the line and had to shift up to 4th. Could it be possible that perhaps that extra gear change is costing that additional tenth of a second? In hindsight, I feel as though the car would have enough in it to run in 3rd to the line. I might give that a try when I go back in the next week or so...

In reality, I know that a sub 13 is nothing special to write home about where others are running 11's, 10's etc. Although I still think a 12 with the std turbo is a good achievement (and realistic goal) so I'm gonna keep trying till I get it. Then perhaps I'll upgrade the turbo and go for 11's instead :D

I was doing consistant 1.9 60" time's on all three 13.1 runs that I did on the day.

What mph did you run?

Also, did you shift into 4th before the finish line? I found that I was always just about on the rev limit just before the line and had to shift up to 4th. Could it be possible that perhaps that extra gear change is costing that additional tenth of a second? In hindsight, I feel as though the car would have enough in it to run in 3rd to the line. I might give that a try when I go back in the next week or so...

In reality, I know that a sub 13 is nothing special to write home about where others are running 11's, 10's etc. Although I still think a 12 with the std turbo is a good achievement (and realistic goal) so I'm gonna keep trying till I get it. Then perhaps I'll upgrade the turbo and go for 11's instead :D

+

I ran 107mph, so looks like you could do with a few more mph. I was definately in 4th, 3rd can't go to 170kph.

When I got my car I always wanted to run a 12, not a 13.

My car is what I'd call a street car but I don't consider it quick. Just under 200rwkw with a nice power band and 1350kg I should crack into the high 12's with a decent launch.

I still don't really think that's that quick though... so yes I think 13 isn't cutting it (atleast for me).

Maybe it's fast and the furious influenced ... "I owe you a 10 second car" lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
    • Mine's a bit bigger at 70x150mm roughly. The spots are flat, just can feel the edges if I dig my nail into it. I did fix some other other ones by both using my finger to sand that small spot (I'm a bit wary of doing this and creating hot spots and a bigger mess) and I also did sand over it flat and others, but this also worried me a bit because if I create an overall low spot on the panel on paint that is good.  Correct me if I'm wrong but as long as it's flat even if I can feel the edges, I can put filler because it will all be level once I sand it? I can see myself going in a circle after sanding guidecoat with 320 grit if for example the panel is flat with my hand but because I sanded the guidecoat I could have created a low spot again somewhere. Unless where I'm going wrong is what I mentioned previously where I didn't go low enough on the grits. It's 1 step forward and 2 step backwards here haha. I'll probably need to experiment with it more. Last time I go back to bare metal lol.
×
×
  • Create New...