Jump to content
SAU Community

Rb25 Turbo Fuel Reg

MonstaS4

By MonstaS4,
in Engines & Forced Induction

 Share

Recommended Posts

MonstaS4 Collaborator

MonstaS4

Posted
Posted

Had my RB30DET on the dyno today hoping to up the boost to 15psi. Problem is it started to lean out at 12psi and feeding in more duty cycle to the injectors didn't seem to have any effect on the A/F ratio. I have a Bosch 910 pump which should be good for 450-500bhp, 550cc injectors and am using the standard turbo pressure regulator. My tuner thinks the reg is not holding the pressure high enough on boost.

Is this a fair call?

He has suggested a Malpassi, but i remember hearing that the pressure can fluctuate a little with these. Anyone have FIRST HAND experience with this?

Link to comment
https://www.sau.com.au/forums/topic/83123-rb25-turbo-fuel-reg/
Share on other sites
BHDave Grand Master

BHDave

Posted
Posted

Did anyone check the fuel pressure when this happened? It's pretty easy to spot when the pressure stops rising with boost. If the pressure increases and then hits a wall then it's the pump.

My malpassi allows fuel pressure to fluctuate by about 1 psi eachway.

As nismod has stated it is worthwhile running a dedicated power feed to the pump with a relay triggered off the current pump power feed. It also eliminates the fuel pump speed control.

The 910 may be a bit undersized for your application, an 040 intank pump is pushing it at 260rwkw and the 910 is a bit smaller (i think).

MonstaS4 Collaborator

MonstaS4

Posted
  • Author
Posted

We ran out of time to hook up a pressure guage on the day. What i plan to do today is run some compressed air at 12psi into the reg and measure how much fuel is returned. At the same time i'll check the pressure. This should tell me... a) how much fuel the engine can use without the pressure dropping off and B) if the reg is actually working correctly.

Dump_pipe, I bought a R33 DE head for the conversion and changed the reg for an R33 DET unit. Part numbers are definately different. I guess the DE reg dosn't have the rising rate ability that the DET reg has.

gtst25 Proficient

gtst25

Posted
Posted
do they make direct swap nismo ones to suit?

Yes they do - mine cost 170aud delivered a year ago, very easy to fit too. I've also been told that melpassi's don't hold good steady pressure - haven't had first hand experience though with the melpassis but with the fuel press guage on the dyno my nismo held rock solid fuel pressure with a bosch 044- no flicker at all. But as everyone seems to say you don't need an adjustable reg unless going crazy on power or want to put more rail pressure.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • myrbgivesmeheadaches
      RB25DET NEO Cylinder Head

      By myrbgivesmeheadaches · Posted

      Did this end up working? Did you take some pictures?
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And finally, the front lower mount. It was doubly weird. Firstly, the lower mount is held in with a bracket that has 3 bolts (it also acts as the steering lock stop), and then a nut on the shock lower mount itself. So, remove the 3x 14mm head bolts , then the 17mm nut that holds the shock in. From there, you can't actually remove the shock from the lower mount bolt (took me a while to work that out....) Sadly I don't have a pic of the other side, but the swaybar mounts to the same bolt that holds the shock in. You need to push that swaybar mount/bolt back so the shock can be pulled out past the lower control arm.  In this pic you can see the bolt partly pushed back, but it had to go further than that to release the shock. Once the shock is out, putting the new one in is "reverse of disassembly". Put the top of the shock through at least one hole and put a nut on loosely to hold it in place. Put the lower end in place and push the swaybar mount / shock bolt back in place, then loosely attach the other 2 top nuts. Bolt the bracket back in place with the 14mm head bolts and finally put the nut onto the lower bolt. Done....you have new suspension on your v37!
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      And now to the front.  No pics of the 3 nuts holding the front struts on, they are easy to spot. Undo 2 and leave the closest one on loosely. Underneath we have to deal with the wiring again, but this time its worse because the plug is behind the guard liner. You'll have to decide how much of the guard liner to remove, I undid the lower liner's top, inside and lower clips, but didn't pull it full off the guard. Same issue undoing the plug as at the rear, you need to firmly push the release clip from below while equally firmly gripping the plug body and pulling it out of  the socket. I used my fancy electrical disconnect pliers to get in there There is also one clip for the wiring, unlike at the rear I could not get behind it so just had to lever it up and out.....not in great condition to re-use in future.
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      Onto the rear lower shock mount. It's worth starting with a decent degrease to remove 10+ years of road grime, and perhaps also spray a penetrating oil on the shock lower nut. Don't forget to include the shock wiring and plug in the clean.... Deal with the wiring first; you need to release 2 clips where the wiring goes into the bracket (use long nose pliers behind the bracket to compress the clip so you can reuse it), and the rubber mount slides out, then release the plug.  I found it very hard to unplug, from underneath you can compress the tab with a screwdriver or similar, and gently but firmly pull the plug out of the socket (regular pliers may help but don't put too much pressure on the plastic. The lower mount is straightforward, 17mm nut and you can pull the shock out. As I wasn't putting a standard shock back in, I gave the car side wiring socket a generous gob of dialectric grease to keep crap out in the future. Putting the new shock in is straightforward, feed it into at least 1 of the bolt holes at the top and reach around to put a nut on it to hold it up. Then put on the other 2 top nuts loosely and put the shock onto the lower mounting bolt (you may need to lift the hub a little if the new shock is shorter). Tighten the lower nut and 3 upper nuts and you are done. In my case the BC Racing shocks came assembled for the fronts, but the rears needed to re-use the factory strut tops. For that you need spring compressors to take the pressure off the top nut (they are compressed enough when the spring can move between the top and bottom spring seats. Then a 17mm ring spanner to undo the nut while using an 8mm open spanner to stop the shaft turning (or, if you are really lucky you might get it off with a rattle gun).
    • Duncan
      V37 Suspension change

      By Duncan · Posted

      You will now be able to lift the parcel shelf trim enough to get to the shock cover bolts; if you need to full remove the parcel shelf trim for some reason you also remove the escutcheons around the rear seat release and you will have to unplug the high stop light wiring from the boot. Next up is removal of the bracket; 6 nuts and a bolt Good news, you've finally got to the strut top! Remove the dust cover and the 3 shock mount nuts (perhaps leave 1 on lightly for now....) Same on the other side, but easier now you've done it all before
×
×
  • Create New...