Jump to content
SAU Community

Recommended Posts

i put on a high flowed, steel bladed VL turbo onto my rb20det and originally spooled up at 4 grand which i was told was about normal...

anyways i had a turbo rattle so i pulled the xhaust off to find out the wastegate flap in the back of the turbo was loose, so we bent the wastegate actuator arm to tighten it up... now the car spools up at 2100rmp and 15psi by 2600rpm, is this safe having the wastegate so tight???

does anyone know???

anyone got a VL T on a rb20det wats your spool up???

thankyou

Link to comment
https://www.sau.com.au/forums/topic/83474-rb20det-with-vl-t-quick-spool/
Share on other sites

Can't really be that much of a problem I wouldn't think

Makes sence that if the wastegate was loose, the air was bypassing the turbine, hence late spooling.

Count your blessings that you are fully boosting at 2600 on an RB20 with high flow, plain bearing turbo!!!

BASS OUT

just forgeys and bored out 20"....

neways on the topic does anyone know if this is dangerous in regards to wastegate being so tight?

if you got some headwork doen when you got the rebuild done it would make it spool quicker. By headwork im referring to a port and polish or bigger valves.

its got me f*#%#@ but its good tho well sort of its a bit too responsive.

how ever if i give boost up and let go after my flutter there is a small hissing sound which goes away a couple of seconds later!

could this be beacuse the door closes so quickly sum air is still stuck and can only just escape out not flow out like before?

or is this a diffrent problem?

i would like to know how a bigger turbo.. hiflowed... t03 off a VL that would normally come on around 2500 on the 3ltr...

comes on almost the same as a motor 1000cc less...

sorry but i might not be an xpert but i know enough!

and yes it is a VL T hi flowed and yes it really does have steel blades

and for sure its bigger than my rb20 turbo

By the sounds of it that spools up to quick,are you sure it is a flowed VLT turbo?

im in the backward case lol i have the RB20 T03 on my RB30DET lol spools up 2 fast just waiting 4 a clutch change and ill be putting my TO4B on but yer thats seems 2 be a very good spool up time for an old timer T03.

mine comes on full boost like 2000rpm or somthin im only running 10 psi and making 150rwkw.

whats it like up top end like duz it tapper off and at wat RPM and also what exhaust AR you got just asking if you know cause if you have like a .64 AR and it spools up that fast on a 2Lt thats mad maybe u found a cheap way to upgrade ya turbo lolololol ??

The RB20DET turbo is a little small for the 3ltr. :P

I find it has the meat of the power between 2000-3500rpm, after that it doesn't feel as nice but still rev's to ~5000rpm where it asks for a gear change.

if I over rev then it drops the next gear out of the meat of the power and instead of acclerating and making more power it accelerates as power drops off :D

Its a bad match in the R32, especially with its short gearing.

yw its very intresting like i am happy with the power form the rb20 turbo i think this one has more punch and i can boost higher with the steel blades but yeh i agree with your Rpm vs power! i have loosend up the wastegate and now i got spool at 2800 15psi by 3400rpm or there about i think thats a little bit better for the rb20det engine, but yeh i dunno i get dynoed in two weeks i was at 160kw before hand lets see wat happens now!

The RB20DET turbo is a little small for the 3ltr. :P

I find it has the meat of the power between 2000-3500rpm, after that it doesn't feel as nice but still rev's to ~5000rpm where it asks for a gear change.

if I over rev then it drops the next gear out of the meat of the power and instead of acclerating and making more power it accelerates as power drops off :)

Its a bad match in the R32, especially with its short gearing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
    • So, a bit of a side trip, but one that might be interesting for people with JDM cars and japanese head units. I know @Pac previously posted about a carplay/android auto adapter he installed which used the AUX input, and @V35_Paul put in one of the Tesla style units that replace both screens. The option I went with was a Lsait LLT-YF-VER5.87_2 (https://www.alibaba.com/product-detail/Lsailt-8GB-Android-Multimedia-Interface-for_1601187633672.html). Price was $1,150 for a single unit although they are much cheaper if you are willing to buy 2....$857ea. Make you you get the version 2 not version 1, it is faster and has a better UI - this is the manufacturer listing: http://www.lsailt.com/product/348.html. BTW if you've never bought from Alibaba before, don't be concerned....these guys can't stay in business unless they are responsive, ship fast etc, they were excellent (probably faster shipping than most local places) So, this was my task for a lazy Sat afternoon....looks complex but was all done in a few hours (it probably helps that I had some of it apart before so it was a bit familiar). I also decided to add a HD USB drive recorded at the same time and the unit also supports an aftermarket reverse cam (if you don't want to retain factory) and also AV in and HDMI out It looks much worse than it is, in fact in was genuinely all plug and play (no custom wiring at all). This video was pretty good (skipped a few steps), unfortunately they are an Aussie seller but no longer sell this unit (I guess Carplay/AA adapters are easier to install and much cheaper) https://www.youtube.com/watch?v=T5hJfYOB8Dg
×
×
  • Create New...