Jump to content
SAU Community

Recommended Posts

OK, well it is 2 tank fulls later (800k's) and I can safely say replacing the lambda sensor made no diference what so ever to the fuel economy. It definitely runs nicer, doesn't hesitate when full throttle is applied after long periods of idling (damn Sydney traffic) and cruising. But fuel ecomomy is totally unchanged.

Gotta get that exhaust on and tune it up some more on the dyno. Just need a spare few hours.

:( cheers :)

  • 9 months later...
Nissan recommends changing them every 40,000k's. They don't "wear out" in a mechanical sense. They just get contaminated and don't read the A/F ratios properly.

Interesting to say the least. So how do you know when to replace them? It's not cheap enough just to do it for the sake of it.

How sensitive are they to being knocked around. A friend dropped his once on the bench and it would not work properly after that. I recently dropped mine while doing the dump pipe upgrade - How do I know it is still working?

Would really be interested to know how they work internally?

They use some sort of chemical reaction to create a voltage once they are at the right temperature (which is why they have heater wires as well) THe chemicals get tired after a while and dont work anymore.

The best way to tell if its stuffed is to use a consult cable to monitor the voltage, stuffed ones read 0 or jump around at odd times. Unfortunately working ones jump around a bit too so it is hard to tell if it is dying unless you have a gtr (2 sensors so you can compare voltage)

  • 1 month later...

I took my car out to CRD to get tuned a week ago - they told me my o2 sensor was stuffed and told me a new one would cost $300+ as well as labour charge.

I get <200kms from a tank, if the o2 sensor was stuffed when they tuned it, does that mean it needs tuning again when i put my new o2 sensor in? or does the wide band one they use for tuning mean that it would have been tuned nicely anyway?

If i replace a stuffed o2 sensor should i immediately see an improvement in fuel economy?

Does anyone have an online link to buy an o2 sensor online? to save me a trip to repco...

And is their any adavantage to buying the genuine nissan part as opposed to the falcon part?

i have a falcon one and it works fine, no problems.

Thanks terminal - im thinking i will try to get a genuine part, or at least one that i dont have to change the wires on, would cost me more to get someone to change the falcon one over than it would to spend the extra on the genuine part.

I am taking it that all of this advice is relevant to R33 gts-t owners, not specifically stageas?

Thanks terminal - im thinking i will try to get a genuine part, or at least one that i dont have to change the wires on, would cost me more to get someone to change the falcon one over than it would to spend the extra on the genuine part.

I am taking it that all of this advice is relevant to R33 gts-t owners, not specifically stageas?

The Falcon lambda sensor I used cost $78 from Repco. last time I checked the genuine Nissan one was $180. I don't think anyone is going to charge you $102 to swap over a plug, it's a 10 minute job.

:) Cheers :P

The Falcon lambda sensor I used cost $78 from Repco. last time I checked the genuine Nissan one was $180. I don't think anyone is going to charge you $102 to swap over a plug, it's a 10 minute job.

:) Cheers :)

Change of plan

I bought a falcon sensor from Repco i think it only cost me $58 (hope its the right one)

The auto elec is charging me about $70 to fit it... It was going to be a 2 week wait for the genuine nissan part.

Quick question, can the power FC be tuned with a faulty o2 sensor? i.e. does the wide band sensor they stick in the exhaust mean that it doenst matter about the faulty one up front?

The reason i ask this is because i just paid for my car to be tuned, and when i rang up complaining about fuel issues they told me my o2 sensor was buggered... So did they tune it right and the new sensor will fix my problems? or did i get ripped off?

Change of plan

I bought a falcon sensor from Repco i think it only cost me $58 (hope its the right one)

The auto elec is charging me about $70 to fit it... It was going to be a 2 week wait for the genuine nissan part.

Quick question, can the power FC be tuned with a faulty o2 sensor? i.e. does the wide band sensor they stick in the exhaust mean that it doenst matter about the faulty one up front?

The reason i ask this is because i just paid for my car to be tuned, and when i rang up complaining about fuel issues they told me my o2 sensor was buggered... So did they tune it right and the new sensor will fix my problems? or did i get ripped off?

Depends on what fuel issues you were complaining about, all the tuning under load they'd have used their Wideband O2 for, and your factory narrowband isn't part of the equation. But if your mixtures are wrong under light load and idle, and the Power FC is setup to use closed loop with the factory narrowband, then a stuffed one would be a problem yep.

How do you mean you've got fuel issues?

Depends on what fuel issues you were complaining about, all the tuning under load they'd have used their Wideband O2 for, and your factory narrowband isn't part of the equation. But if your mixtures are wrong under light load and idle, and the Power FC is setup to use closed loop with the factory narrowband, then a stuffed one would be a problem yep.

How do you mean you've got fuel issues?

Fuel issues are only getting 200km per tank which is costing me a fortune. doesnt seem to matter how i drive it (hard or soft) i still get terrible fuel economy... having a new o2 sensor installed as we speak

Fuel issues are only getting 200km per tank which is costing me a fortune. doesnt seem to matter how i drive it (hard or soft) i still get terrible fuel economy... having a new o2 sensor installed as we speak

Then they could be talking about lack of closed loop control giving you poor cruise/idle fuel economy(due to stuffed O2). Generally in a full tune, they would input fuel values for all conditions that were close to ideal, so you shouldn't get shocking fuel economy after a good tune, even without closed loop control.

I don't get heaps better than that myself (used 16L to do 71km's around town the other day, but prob too much boosting). But anyway, I thought mine was too rich, and thought factory O2 was stuffed. Last night I put my LC-1 Wideband O2 sensor on it and went for a drive, 14.5:1 under all idle and cruise conditions! That surprised me, thought it'd be far worse.

Would be very much to your advantage if you could borrow/buy an Innovate Motorsports LM-1/LC-1 and analyse your mixtures, then you'd know before/after, and not have to put all trust in what the workshop tells you. Not too mention you'd then have crucial gear for tuning your ecu yourself if you ever wanted to.

I reluctantly paid $400 (NZ) for mine(and display it on my old laptop), but now I love it and can't imagine not buying it, I'd have no idea what my cars are doing!

Bottomline, it's hard to diagnose fuel troubles, especially with an aftermarket ecu, without some kind of AF reading gear.

Let’s clear up this “closed loop tuning” issue. There is no such thing as “closed loop tuning”, the standard ECU has a simple lambda aim table loaded into its mapping. In a Power FC that is in fact one number, around 15 to 1 A/F ratio.

This means whenever the parameters are met (idle or cruise) the ECU reads of the standard (narrow and slow) lambda sensor and tries to hit the targeted A/F ratio. So it increases or decreases the injector duration continuously trying to keep at 15 to 1. As long as the lambda sensor is working correctly the ECU will always aim for its target A/F ratio, hence there is no tuning required.

Remember with all closed loop running it doesn’t happen instantly, the throttle opening has to be constant, the rpm has to be stable and the (slow and narrow) lambda sensor has to have enough time to read off the A/F ratio and tell the ECU what it is.

This is where a slight improvement in fuel economy can be gained by utilising a fast and wide lambda sensor. By tuning the fuel map locations around the closed loop location (idle and cruise) to give around 15 to 1 A/F ratios. This means that you save that little extra fuel while the ECU is fiddling around reading the lambda sensor etc.

If you have a read of the Tech Edge thread in Forced Induction, I go into some detail on how I tuned the idle and cruise A/F ratios.

:devil: cheers :down:

Fuel issues are only getting 200km per tank which is costing me a fortune. doesnt seem to matter how i drive it (hard or soft) i still get terrible fuel economy... having a new o2 sensor installed as we speak

A perfectly working lambda sensor is unlikely to improve the fuel economy from 200 k's per tank. Maybe 20 k's, depending on how much time you spend at cruise or idle. If it's a lot of the time while you are driving, then you might get 15%, but if you spend hardly any time idling and cruising then it won't make much difference at all.

Personally my guess would be you have other problems, not the least of which is tuning.

:devil: cheers :down:

A perfectly working lambda sensor is unlikely to improve the fuel economy from 200 k's per tank. Maybe 20 k's, depending on how much time you spend at cruise or idle. If it's a lot of the time while you are driving, then you might get 15%, but if you spend hardly any time idling and cruising then it won't make much difference at all.

Personally my guess would be you have other problems, not the least of which is tuning.

:wave: cheers :D

I just paid to have it tuned...

Is there anything else it could be?

I spend a lot of time at idle, but not much at cruise... i cant afford to keep running the car like this.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The cross sectional area of a circular hole scales with the square of diameter. So a 2mm diameter hole is 4x the area of a 1mm hole. Not double. The 1.7mm hole is nearly 3x the area of a 1mm hole. You do not need restrictors at both ends of the oil supply line. If you have new, additional restrictors at the turbo end, that you did not have before, then you do not need a restrictor at the inlet end.
    • Hi all. Been a while but things are moving along. I just have something that I am wondering about. Since I will use OEM turbo oil pumbing, I got myself a new bolt, the one that goes into the engine block oil feed. As I recall (and see visually) this bolt comes restricted with I think a 1.7mm hole? Not quite sure but it was something around that size. The turbos have 1mm restrictor bolts installed, as necessary due to ball bearings and my higher oil pressures. Can I now just use that OEM bolt with the 1.7mm hole in for the engine block or will this actually be too much oil flow restriction and I have to drill it out first? In my head it would make sense for the bolt to be at least 2mm wide as both turbos take "1mm of oil flow". Do let me know if my logic is flawed here, I just want to make sure I don't kill my turbo bearings with too little oil. Don't know if I can trust the saying I read somewhere that ball bearing turbos essentially only need an oil mist
    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
×
×
  • Create New...