Jump to content
SAU Community

Removing The Front Bar Of A R33

Bunta

By Bunta,
in Exterior & Interior Styling

 Share

Recommended Posts

Bunta Grand Master

Bunta

Posted
Posted

Ok Guys I am having a problem with removing the M spec front bar from my S1 r33gtst. I have removed the bolts attaching the bar to the side skirts I have removed the 3 screws under the grill and I have unattached the bar from the lining inside the guards. And unplugged the indicators. The bar still seems to be attached near the headlight area. When I look up under the headlights there is fairly large white square clip. I can’t move this but. Does this mean I need to remove the headlights to get the front bar off? Any help would be greatly appreciated, as I can’t take it any more this bar needs to come off! Thanks guys…also does anyone know of a book that has this type of stuff in it. I got the tech manual but it is more for mechanics than a backyard tinkerer like me. Thanks heaps guys! :D

Link to comment
https://www.sau.com.au/forums/topic/84089-removing-the-front-bar-of-a-r33/
Share on other sites
arm85 Community Regular

arm85

Posted
Posted

Hey mate, i have done this anumerous times now the first time is definately the hardest the best thing to do is get a long skinney flat hear screwdriver and gently pry the clip up while pulling on the front bar, easier if you get someone to give u a hand to hold the bar, do this on both sides and the bar should come off if you have all the bolts un done.

JCMarshall_Law Proficient

JCMarshall_Law

Posted
Posted

Is it eaiser just to unbolt the reo (2 bolds either side), and the bolts either side near the guards. The whole lot comes away.

I have not done it but I have recently had a new bar fitted and the group who did it took the whole lot off then unbolted the bar from the reo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • BASHERnissan
      TPS voltage RB25DET

      By BASHERnissan · Posted

      Hi guys my TPS voltage is reading over 2v at idle.  My Haltech ECU is reading around 40% throttle position at idle also which is really strange. Note the actual throttle position sensor is brand new…    anyone have any experience with this or know how to calibrate it on Haltech ? 
    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      The OEM disk will not work on any AEM ECU, you need to use the one they made. You shouldn't have to flip the CAS or whatever you were describing, if you set the ignition sync offset correctly it can't backfire. Make sure you're using a spark plug lead on coil 1 instead of the timing loop to avoid weird issues with the timing light. Double check that your timing settings are actually correct, like is the 24 tooth configured correct or should it actually be 12 teeth for 1 crank revolution? I also found this: 305817248-AEM-Undocumented-Settings-v1-2.pdf    
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Yeah, I don't believe the M35 uses a deadhead system.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      Have you done your thinking backwards? 3 bar, 43.5 psi pressure drop being the presumed specification for an injector, means you need 3 bar upstream when they are firing into atmospheric pressure, and more upstream pressure than that when on boost (you add your boost to your rail pressure to maintain 3 bar across the injector) and you need..... less pressure upstream when you have vacuum in the manifold. So, presuming that you're idling at -10 psi, then you only need ~23 psi in the rail. I realise that I did not need to say all of that to you specifically Matt, once you'd realised your mistake. It's mostly there for complete clarity for others.
    • Dose Pipe Sutututu
      RB25 Drama's

      By Dose Pipe Sutututu · Posted

      Have you reached out to the guys at Spool Imports? They are a Ross dealer, I can imagine they would have the rings just sitting on the shelf (I could be wrong).  
×
×
  • Create New...