Jump to content
SAU Community

Recommended Posts

Got some 18x10.5 +20 for my r32 GTR.

Rear guards are rolled, anyone know if I will need to roll the front?

Tyres are 265 35, ride height is standard atm.

Cheers

You should be ok. They will stick out 2mm less than my 18 x 10 +12's. I've just lowered mine a bit more last night

And the only thing they started to hit was the inner liner on the drivers side. I'm gonna lift back up 10 mm all round.

hi guys, just wondering if 245/35s will fit on a 18x10" rim? without looking stupid... as i worked out my speedo will read more correct! as i currently run 245/40s and they are a little stretched and reads slow.

has anyone done this?

cheers..

Ok i've been through about 20 pages in the thread but can't find anyone that has put R34 GTR VSpec rims on an r32 GTST so just wondering if anyone has done it or if 18x9 +30 would fit on R32 GTST rear guards which have been pulled and rolled, I have GTR front guards which arn't rolled and pretty sure they would fit.

Thanks Tim.

How would 18X9.5 +15 Drifteks fit on a R33 GTS? Mods needed?

BTW I have slightly rolled guards and run about 2 degrees camber on rear and BC coilovers all around (pretty high atm)

Thanks in advanced :thumbsup:

Ok i've been through about 20 pages in the thread but can't find anyone that has put R34 GTR VSpec rims on an r32 GTST so just wondering if anyone has done it or if 18x9 +30 would fit on R32 GTST rear guards which have been pulled and rolled, I have GTR front guards which arn't rolled and pretty sure they would fit.

Thanks Tim.

Tyre size? Fronts will be fine. Rears will be fine depending on camber / tyre size

How would 18X9.5 +15 Drifteks fit on a R33 GTS? Mods needed?

BTW I have slightly rolled guards and run about 2 degrees camber on rear and BC coilovers all around (pretty high atm)

Thanks in advanced :thumbsup:

Should be able to get away with a 225/40 tyre all round

Sorry, will try and get some pics up soon, turns out the retards that put them on at ozzy decide to put a 9.5 on the front left and a 10 on the front right, with a 9.5 on the rear right and a 10 on the rear left... f**ked up my alignment. thought it looked funny!

its sitting reasonably low, not where i want it though..

Skyline model = r33 gtst

Wheel diameter = 18

Wheel width =10 and 12

Wheel offset = -6/-17

Tyre size = 255 and 275 stretched on

Modifications to fit = rolled and flared all round + 50mm blot on flare + low camber

definately need pics!

you will have to take out the inner guard linings and depending how low you are you will have to move the wiring loom up. Also i had problems with scrubbing on full lock on the firewall which i bashed with a mallet to get more clearance.

i ran 18x10+10 with a 225/40 on the front

IMG_0369.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
    • I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
×
×
  • Create New...