Jump to content
SAU Community

Recommended Posts

For now I think I'll leave it as is.

Only to test the waters and see if I get any attention for having them.

Also my funds have dried up a little haha

I think the law is 25mm outside the guards? Not too sure on that one, is just what I heard.

I haven't got any cop attention at all, had cops pull up next to me and behind me.

But yeah the more you lower your car the more camber it will naturally give it. Anyway it does look boss man - check out my pics a few pages back - black on black, same rims haha.

EDIT: I see you commented on a pic of my car saying it was perfect fitment haha.

Edited by voncina

I saw in another thread on here where the guy rolled the front guard lip tight such that one of the tabs was holding the liner like a clamp. So basically kept the liners, and rolled tight. Not sure how robust that would be though.

Will see if i can find it again...

Found it:

http://www.skylinesaustralia.com/forums/topic/401848-trying-to-fit-my-dream-wheels-te37/page__view__findpost__p__6393854

You can see in one of the photo's how they used the tab to hold in the liner. Personally I would prefer to keep my liners when I roll. This looks like an option, but would be keen to hear others thoughts too.

in the pic below shows clearly that the tabs are not holding in the plastic guard liner (splash guard). Also looking at the pic seems it has a small flare pushing the guard out slightly

also this has not been rolled perfectly flat

2012-06-09111817.jpg

Edited by Frosty

Put new wheels on today,(17x9+22 enkei rpf1s) and have ran into a slight problem, regarding those plastic guard liners.

They scrap on corners that have either got a bit of a dip during the apex or slight elevation or while descending.

If i remove them completely, is it possible for the wheel to still hit the guard at all? Am i able to push the guard out at all to stop this happening?

It used to happen even with stock R33 wheels as well. Any info would be great.

Car had an alignment today, it was only slightly out.

The car is sitting on bilsteins and king springs, it isn't as low as others i have seen, i can stick my foot between the wheel and the guard. With the new wheels pretty easily, at slow speeds aka 50kmh, on the stockies it did it only on corners that had a really bad dip during the apex (only in the hills), when the G's would have been at there highest.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...