Jump to content
SAU Community

Recommended Posts

check if there is a leak under the power steering resivoir..(??) the little bottle which has redish liquid inside... also check how much inside, should be neary full.... i dunno about r32s, (because I dont like them) but in my r33 it had a different diff and there was also a power steering fluid bottle in the boot .. if you have one of these (dont think you would) check it too

The HICAS controlles the power stearing, there is a high speed and low speed mode. If the speed wire is cut it get's stuck in high speed mode. I had the same prob, I soldered a bridge wire from the speedo to the HICAS speed sensor wire.

The best way to test is to get a multi meter. the HICAS box in the boot (on the drivers side in my car) has a yellow wire with a green trace, if you unplug the conector and put a probe with a extention wire on it, and put the lead round to the drivers seat. Now you need to pull out the speedo, there should be 3 plugs in the back of it. on the middle plug is the other end of the yellow/green wire. Put the other end of the probe there, and put the multimeter on resistance mode. If you get a reading your wire is fine. if not you have to find where the break is.

i had the same problem... last monday i blocked my stock BOV so i can get my car to flotter.. while drivin it the hicas light came on and my power steering stifended up... now today, i just got my Apexi BOV put on and it happend again, but this time i hav'nt blocked off the return pipe form the stock BOV in to my air intake. what should i block it off wit?? its steel so i cant really cut it...a ny idea's??

My HICAS light comes on when I turn left!

I had the wheels aligned not long ago and have had the problem since....

SAME!!

my wheels are badly aligned tho, i hope getting an alignment can fix mine

I wouldn't wast too much time with HICAS, a locking bar might be the best solution and just get rid of it.

At high speed,active HICAS can make the car feel pretty nervous.

more scary when it dosn't work, and moves under high force, or bumps in the road.

Edited by sav man

so no 1 realy knows how to fix it?? i noticed in the skyline R32 the power stearing aint that light? could this be my hicas or are they always like this? or could this be because its stuck in hi speed mode?

i had a look and my power stearing fluid was 2 high.. so i dranied some and now it dosnt come on as often! tonight i had a little race with a 180 and just after it the hicas light came on...

i am still to try this speed wire test.. but i dont have the right equipment!

thanks

  • 3 weeks later...

I am experiencing exactly what you are experiencing Drift Squad except the Hicas subframe has been removed on my R32 GTR i.e. no more Hicas. The ECU has also been reprogrammed/chipped. The hoses were also plumbed back from where the Hicas was removed.

The car has power steering for the first few minutes and then reasonably quickly the steering becomes heavy at which time the Hicas light comes on until the car is turned off. When it is started again the above symptoms are repeated.

Any ideas?

so no 1 realy knows how to fix it?? i noticed in the skyline R32 the power stearing aint that light? could this be my hicas or are they always like this? or could this be because its stuck in hi speed mode?

i had a look and my power stearing fluid was 2 high.. so i dranied some and now it dosnt come on as often! tonight i had a little race with a 180 and just after it the hicas light came on...

i am still to try this speed wire test.. but i dont have the right equipment!

thanks

HICAS has been covered to death on this forum. A search would have told you everything you need :P

Yes, it can be fixed (assuming the mechanicals and electronics aren't damaged). Usually its one of the following or a combination (in rough order of occurence):

1) Low powersteering fluid.

2) Aftermarket steering wheel with wrong or incorrectly installed BOSS kit.

3) Poor wheel alignment.

4) Speed sensor wire has been cut.

5) Leaking powersteering hoses.

ah, the BOSS kit BTW is HBK ON-115, not the ON-110

The ON-110 is for the NON-HICAS GTS-ts (and GTS4's I think)

The ON-115 is compatible with HICAS

incorrect

if it comes with the plug its compatible and it does

last night i changed my steering wheel and when i fitted the new 1 its slightly off centre, it caused the light to come on...

easy fix though.

Edited by silver gts-t

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...