Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

Contact Details: [email protected] or ring me on 0400-77-99-78

Hi there, im sure most of you know the story. As a resolution a replacement vehicle from J-Land is on the way for me - I'm all smiles and credit the import company for their professionalism and efficiency shown in the matter. As for this beast it is time to split her up and move on..

I have attempted to list everything that I can think of, if there is something that I have failed to mentioned that your chasing please let me know. Photo's are easily provided for those with genuine interest. I do not mind sending via COD providing a small deposit is made into my account. Cheers!

Engine bay and Driveline

RB26DETT motor complete with factory turbochargers, loom, factory ECU and HKS FCON computer $6000

RB26DETT gearbox $1100

R32 GTR rear diff and cradle **SOLD**

HKS Twin air pods (needs new filters) $100

HKS ATTKD Intercooler piping for no AFM setup $150

R32 GTR Radiator $200

R32 GTR Fuse Box $80

R32 GTR Tail shaft $200

100mm Intercooler with decent sized dent **SOLD**

Air Condenser and Compressor $200

R32 GTR Fuel pump $100

R32 GTR Fuel tank $80

Suspension related

R32 GTR 16" wheels (need a clean and some decent rubber) $700

R32 GTR Complete set of calipers and cross drilled rotors (not willing to seperate) $700

R32 GTR Hubs $100 each

R32 GTR Rear Sway bar **SOLD**

Interior parts

R32 GTR Front seats $700 **SOLD**

R32 GTR Rear seats $350

R32 GTR Dash with no bubbles $200

R32 GTR Dash with clock $150 **PENDING SALE**

R32 GTR Centre console surround $100 **PENDING SALE**

R32 GTR Instrument cluster with 73,000km's $100 **SOLD***

R32 GTR Air conditioner console $200

R32 GTR Centre console gauges $100 **SOLD**

R32 GTR Steering wheel $100

R32 GTR Door trims $100 each

R32 GTR Rear trims $80 each

Body parts

R32 GTR Bonnet in white with latch $550

R32 GTR Grill (one clip broken) $100

R32 GTR Driver side fender in white $250

R32 GTR Passenger side fender in white $250

R32 GTR Front Bumper in white with N1 slots and lip $400 **PENDING SALE**

R32 GTR Rear Bumper in white $250 **SOLD**

R32 GTR Driver side door $250

R32 GTR Passenger side door $250

R32 GTR Boot with factory spoiler $250

R32 GTR Driver and Passenger windows $50 each

R32 GTR Front headlights $100 each

R32 GTR Indicators $150

R32 GTR Electronic mirrors in white $70 each

I don't know the story so what's the go with the car, did it get damaged in transit?

Do you have the body shell and full wiring harness as this is what I am interested in???

Link to comment
https://www.sau.com.au/forums/topic/85157-sold/#findComment-1543646
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...