Jump to content
SAU Community

I Got My Car!!!

FriniK

By FriniK,
in New South Wales

 Share

Recommended Posts

FriniK Community Regular

FriniK

Posted
Posted

after 6 years of jealosy and yearning for my liner...i finally got it...but theres 1 problem ...my bloody driveway is too steep...scraped the bottom of the lip when trying to get it down the driveway ...now my baby has to sit out in the cold :)

I think its time to get the construction crew in to fix up the driveway...

anybody know any quick fixes to get the car down a steep drivway?...

if so, where do i get the materials to solve the problem....??

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/
Share on other sites
Sl!m Grand Master

Sl!m

Posted
Posted

Yeh thats what I was going to sugest, planks of wood... work a treat. if they dont work.. then your driveway must be reaaaaaaaaly steep!!

welcome to the car owning side of SAU mate, it was about 4 yrs before I bought my r32 :)

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1548968
Share on other sites
MANWHORE Grand Master

MANWHORE

Posted
Posted

sledge hammer :)

but in all seriousness, I have to use planks of wood. if you go to your local bunnings, and buy some offcut 2x4 preferreably 2 bits 1m in length, and lay them down in the gutter.

I only drive my car on the weekend, so it'd not too much hassle, but it'd drive me nuts doing it everyday. If you leave em there, some little pricks might take em.

cheers

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549063
Share on other sites
wilch Grand Master

wilch

Posted
Posted

buy a sheet of that thick checker plate alluminium (Bunnings Dural has them).

Lay that across the front of your driveway, use a hammer drill to drill into the concrete, and use some bolts to bolt the alluminium down. If council complains, unbolt and remove... Then replace when they're gone... :D

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549525
Share on other sites
FriniK Community Regular

FriniK

Posted
  • Author
Posted

Thanks for the suggestions guys, ill give the planks of wood a go for now.....its almost impossible to go in on an angle because its such a small driveway, its not the initial gutter im having problems with its the flat bit just before it enters the garage...basically from the gutter its flat, then it goes down on about a 35-40 degree angle then its flat again ..its the bottom section i had probs with...

I'll stick pics up soon, but its pretty much stock looking sII with stock rims ....(next purchase)

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549681
Share on other sites
SAWAKITA Rising Star

SAWAKITA

Posted
Posted

Need to go side way down.. used to happen to my ex-line with 400R front bar everyday (steep driveway). Just remember to let 1 front wheel reach the ground first then the other.

If still impossible, cheapest way is get a long timber and trim it suit ur driveway. I've seen few tyre shops use this way for customers with LOW cars.

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1549916
Share on other sites
FriniK Community Regular

FriniK

Posted
  • Author
Posted

IMG_2486.jpg

IMG_2500.jpg

My precious...

Still needs some pretty rims....

I should take it out for a proper fotoshoot when i get them...

Anyway ...thanks for looking ...

ill get a foto of the driveway to explain my dilema properly when theres light...

oh yeah...those halogen lights...is it illegal for me to drive with them on?

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1551863
Share on other sites
siksII Grand Master

siksII

Posted
Posted

at my old place my parents bought a sedan that was quite low, couldnt get over the edge going down to the driveway, within a couple of weeks they got construction people in, they jackhammered the concrete down and relaid half of the driveway so it was a smooth angle lol

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1552129
Share on other sites
satanic Grand Master

satanic

Posted
Posted

Huge thread (do a search for Driveway Problems) about driveway problems when I first got my Skyline (well after I lowered it :))... I have one bloody steep driveway and if it weren't for the planks of wood, my front bar would be no more :)

Pros for the wood:

1) They are very very cheap, use offcuts from anywhere

2) Quite light and not too hard to setup

Cons for the wood:

1) Not good in the rain

2) Gets bloody annoying when they start to rot away

3) Depending on your road surface, it will start to destroy itself.

My next plan is to get some steel drainage vents (maybe 2m x 1m) which I can mount on top of the driveway as stated above in a previous post. Not only will this get rid of most of the cons, but will also make a nice addition to my shoddy driveway :D

Just some thoughts...

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1564870
Share on other sites
FriniK Community Regular

FriniK

Posted
  • Author
Posted

Thanks for the suggestions guys, but the real problem isnt entering the driveway from the road, its at the bottom of the driveway. *see attatched* Ive tried reversing it in to no avail.. Close, but no cigar. Anyway, i think the only option is to tear up the driveway and build a new one.

THe red bits on the images indicate where the front would hit if i drove it down front first or reversed it in.

driveway1.jpg

driveway2.jpg

driveway3.jpg

Link to comment
https://www.sau.com.au/forums/topic/85565-i-got-my-car/#findComment-1575619
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...