Jump to content
SAU Community

Recommended Posts

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

- I'll have to look for the hand brake cable & lever

- I will sell the clutch and brake pedals with their brackets/assembly as one piece each. I wont be able to sell the pedals seperatley to the housings. I will take $150 for the clutch pedal assembly (Includes master cylinder) and brake pedal assembly also for $150

Let me know.

Cheers.

Hi all,

Its been a bit hectic getting back to all of your pm's & e-mails, but I'm almost there.

Pm's & emails have been sent to you.

Keep your enquiries coming through. Sometimes it may take a couple of days to get back to you on a particluar part, as they are not all locvated in the one location.

Cheers all

SJ

Hi all,

The only body parts/panels I have left are as follows;

1x Complete Drivers door (including mirror, door trim, switch panel, etc in white) $450 obo

2x rear qtr Glass windows, $50 each obo

1x factory rear windscreen (Window wiper version) $75 obo

I also have the following (and maybe some more, I will have to check)

1x Airbag steering wheel and complete column (with windscreen & indicator levers), $225 obo

1x Complete rear seat, $150 obo

1x Right hand rear tail light (White), $75 obo

1x Rear Bumper bar support, $make me an offer

I will go through the remainder of my parts and list them a little later. For all of you guys out there after the brakes, I do have them, but I will not post a price until I can confirm if I have all of the parts, as i have used parts of the suspension.

Cheers all,

SJ

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...