Jump to content
SAU Community

Recommended Posts

Hi everyone, quick question about my climate control unit. When it's on 18C (manual setting) it blows cold air, all good, but when i turn the dial to raise the temp it starts blowing hot air i.e. on 19C and above it's like the heater is on. So I can be freezing or cooking, no in between. I'm guessing it's stuffed, does anyone elses do this? Is it likely to be the unit in the dash thats all bad (something electrical perhaps) or could it be anything else before I spend the $350 I was quoted for another dash unit?

Thanks

Edited by deano_33
Link to comment
https://www.sau.com.au/forums/topic/86667-climate-control-problem/
Share on other sites

Check the little pipe that sucks air in from the dash to check the temp. On the '33 its a little circle grille near the ashtray (from memory). Not sure where it is on the stag yet. But make sure its not blocked or bent etc as it will misread temperatures.

Does that make sense?

Update: Got another climate control unit from wreckers ($350), didn't fit, different plugs on the back, same number of pins but just slightly different so don't fit. I guess the S1 and S2 stageas are different there. Wrecker is going to try to find one from a S2, don't fancy my chances though. Might have to try Nissan, can't imagine what it would cost......

Had a look at the temp sensor (to the left of the steering column?), seems OK but I don't think that would be the problem seeing as the problem is the same in auto or manual mode?

Hmm, might have to live with it for a while.

Edited by deano_33

My Stagea does exactly the same thing. I just assumed that it might have been sensing that the cabin temp was already less than 19 degrees, so it actually started blowing in hot air to bring it up to that temperature. 19 degrees inside a car with no sun shining in through the windows would actually be quite cool, wouldn't it? But now that I think of it, the times that I have tried it and it has done this have actually been at night. I'll try it again tomorrow, when the outside temp is 36 degrees with 110% humidity and see what happens. Hmmmmmmm

I think the problem could be the thermistor (thermally sensitive resistor) behind the cluster surround.

Try to replace this part first and see how that goes(few dollars i assume), because if it is old it could be sensing mega wrong resistances... and also being the "control" unit of the whole climate sensing idea..

climate20ot.jpg

climate5zj.jpg

Also, it may be dusty, so give it a good blow to get dust off (insulation)

Okay Alexcim I'll have a look, thanks for going to the effort of marking the pic!

Auto/torque converter has pooed itself though in the meantime - feels like a slipping clutch in a manual and can hear metal on metal sound, not good. Getting this attended to atm.

Might be a stupid question, but have you run the diags on the climate control to see what error it comes up with ?

J

No, not a stupid question. You get it into diag mode by holding down the off button and turning the car on right? I tried it and lots of crap comes up, how do you interpret what displays on the screen?

No, not a stupid question. You get it into diag mode by holding down the off button and turning the car on right? I tried it and lots of crap comes up, how do you interpret what displays on the screen?

Cool,

Have a look at page 31 of this doc, it's probably the same as the R33 (fingers crossed).

J

skyline_book.pdf

I thought that if the A/C is in Maunal, the Compressor doesn't come on unless you push the 'A/C' button.

If that is the case, if you select a temp that is lower than the outside, outside air will blow in. If you select a temp warmer than outside, the air will be diverted through the heater.

Does this sound correct?

  • 2 weeks later...

I think mine assumes it's always hot outside, I have to set it to around 25 or 26 degrees to keep myself warm...

Oh, and when adjusting stuff, how do you press the "Hot" button when the Stagea has a dial instead? Do you just turn it up to a warmer temp?

Hey, isn't there a button you can press so that it displays outside temperature?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'd be very surprised if you can buy new OEM mats. But if you can, I want some too!  Do you have links to the variations you found? Also, where are you located? I found that Nengun is happy to list items to purchase but when you do buy them you'll get an email that it's actually discontinued. As far as I know the variations in floor mats are different colour schemes as well as automatic and manual having a slightly different shape. The automatic ones fit into a manual car without issues, but I think you'd have trouble fitting the other way around. I have photos that show the shape difference if you care. FWIW I bought sets of used floor mats in decent condition at yahoo auctions.
    • Hi 🙋‍♂️. Just bought my Unicorn but the interior need some minor work so it would match my expectations ;). I noticed it is hard to get used oem floor mats in good condition so i started to dig if there's any chance to buy set of new ones. I found two websites - nengun and amayama and it looks like one can still buy factory new floor mats in Japan, but thers a small issue. Some mats (i assume genuine, oem ones) are marked as G4900 and these are "discontinued". The ones you can buy are marked as G4911 but i have no idea if these are also oem, made by other producer or some lower quality replacements that looks entirely different. Can anyone help? 😃  P.s. there is also some strange indication - 0V005, 0V015 and 0V505. Any idea what does it mean? Would appreciate any help with this 🙏
    • Hi, Marek here 🙋‍♂️. I finally fulfilled my longtime dream - recently bought Stagea and now waiting for it to arrive in Poland. There's only few of these in my country, and one of the owners  recommended mi this forum as a source of all the info i'd need since now i own one  so here i am.  
    • Version 1 aluminium airbox is.......not acceptable No pics as I "didn't like the look.....alot" Even after all my "CAD", and measurements, the leg near the fusebox just didn't sit right as it ended up about 10mm long and made the angle of the dangle look wrong, the height was a little short as well, meh, I wasn't that confident that Version 1 was going to be an instant winner I might give Version 2 another go, there's plenty of aluminium at work, but, after having in on and off a few times, and laying in the old OEM airbox without the new pod filter and MAF, there may be an option to modify the OEM air box and still use the Autoexe front cover and filter.... maybe This >  Needs to fit in here, but using the panel, and not the pod, the MAF will need to fit in the airbox though> I'm thinking as the old OEM box and Autoexe cover that is sitting in the shed is just sitting around doing nothing, and they are relatively abundant and cheap to replace if I mess it up and need another, it may well fit with some modifications to how the Autoexe brackets mounts to the rad support, and some dremiling to move it get in there, should give me some more room for activities, as I don't want to move the MAF and affect the tune Sealing the hole it requires to stick it in the air box is simple, a tight fit and some pinch weld will seal it up tight  I am calling this a later problem though
    • and it ends up being already priced in as though you're just on 91RON without any ethanol. Car will lose a bit of economy as the short and long term fuel trims bring down the AFR back to stoich or whatever it is for cruise/idle for the engine.  
×
×
  • Create New...