Jump to content
SAU Community

Recommended Posts

i went to my mechanic because i needed to replace my water pump. it was ment to be a $300 job (parts and labour). the night it was done i was on my way to the central coast from sydney and.......i lose all power and my car stalls on the f3???

WTF happened??? :huh:

i spent $220 to get it towed to my other mechanic. the next afternoon i was there while they stripped the motor down. timing belt was 50% of its normal thickness. little strands and belt reminence was everywhere. the head was taken off and just as i suspected...exhaust valves were f@kt! slight scratches on the top of the pistons, but they're ok.

i sent the head to the guilty mechanic and told him to replace the valves, seats and guides.

called him today and he said he's only changing the valves. thats when i called my mum...hahaha he's afraid of her! hahaha (don't laugh! you'd be too). now those three things are being changed and it's getting a port and polish too! :P

the guilty one says he's going to pay 50%

what do you guys think???

btw its an SI r33

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/
Share on other sites

I'm guessing the mechanics screwed up the timing belt while doing the water pump, which in turn caused the valves to fail. But I'm no mechanic...

In fact my mechanic friends regularly tell me that I know f**k all about f**k all. (Although when I try to tell them that the double negative in fact implies that I know everything about everything, they won't have a bar of it...).

So someone more knowlegable respond!

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1568168
Share on other sites

so how much will you be out of pocket if you pay 50% each?

if its less than $400 or so, i would say bite the bullet and pay, then stay away from that mechanic!

after all, time is money. after months spent with lawyers and in court, is it going to be worth the stress and hassle? no.

Warren.

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1569458
Share on other sites

You have to take the timing belt off to change the waterpump?? isnt that strange? Most cars arent like that.. waterpump runs off the alternator belt.

Excuse my ignorance (only just got my 'line and havent had a good chance to have a sticky under the bonnet :) )

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1569709
Share on other sites

$400???? more like $1500-$2000. but thats including a port and polish. hahaha. was doing maybe a little bit over 4000rpm. i have pics on my phone but i can get them onto the computer. show the damaged valves & scrapes on top of the pistons.

it feels weird not driving my car. i drive everyday sometimes have 1 day off a week or month. i miss her!!!

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1569769
Share on other sites

If you can prove that it's his fault ( sometimes very hard ) then he should pay fro everything including the tow . If he replaced the timing belt it maybe esier to prove .

If he refuses you can go to fair trading .

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1571107
Share on other sites

Are you sure that is all the damage that was done? Did you ask him if he even looked at the timing belt because if he did and didnt advise you that it was old/worn he is a lame duck anyways. i'd get your scary mum ( mines scary too) to give him another rev or two and try for a better deal.

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1572207
Share on other sites

i hate dodgy mechanics but can forgive anyone for making a mistake as long as they make good 100%

if he's doing anything by way of reparation you're lucky; you're getting something from him, but it also means he accepts liability. this is good for you in case there are more problems or you want to push for more. it's a no brainer but don't piss him off now or you'll get it back in peices. as for the port and polish make sure it's being done by someone good or or it'll be worse than ever.

the dept of fair trading is your friend in this - they can't stand dodgy arseholes any more than i can. he should make good 100% but if you've agreed to the current arrangement then there's probably not much more that you can do. if you have further troubles don't do anything with this guy, call the fair trading people and tell them the whole story. they will manage the negotiation for you - it's worked for me in the past.

at this stage however don't be disappointed, it's still a good outcome.

hope things work out for you

Link to comment
https://www.sau.com.au/forums/topic/86739-who-should-pay/#findComment-1572257
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...