Jump to content
SAU Community

Recommended Posts

so the HKS GTR only has the pods to make them sounds good?

and those 9s GTRs also, no performance increase from pods?

They probably found it easier to fit their upgraded turbo kits with pods instead of the airbox + the pods look and sound cool

Edited by gtst25
  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

but with the forward acceleration of the car colder air from infront of the car should go into the pod

A car is designed so that there is a low pressure area behind the radiator (the engine bay). This allows the great majority of the air to pass through the radiator and cool the coolant. In the process this air heats up. This is the air that is sucked in by the pods.

This is also why stock air box's have their snorkle fitted up tightly behind the front head light. If they were to just sit it there it would be of no use as the air from the radiator will contaminate it.

A car is designed so that there is a low pressure area behind the radiator (the engine bay). This allows the great majority of the air to pass through the radiator and cool the coolant. In the process this air heats up. This is the air that is sucked in by the pods.

This is also why stock air box's have their snorkle fitted up tightly behind the front head light. If they were to just sit it there it would be of no use as the air from the radiator will contaminate it.

Valid point, but is the pod in that low pressure area "behind the rad"?

Im not saying your wrong but thinking about it I doubt that the air will get all that much kinetic energy transfered to it to keep the same momentum as the car (thus the pod) to allow a majority of it to be sucked in my the pod.

Sure the turbo will create a great amount of suction, but by the time it effects the area where the heated air that cooled down the rad is most of that air should be on its way out of the engine bay or be hit against the engine and bounce elsewhere, some to the pod and most of it elsewhere in the bay...

Eitherway I still am a air box fan, and believe even with a pod mostly cold air will be sucked in.

At the end of the day there is an intercooler to cool the intake air, and if it is a 30+ degree say its just stupid to use drive any performance car (especially turbo) at its full potential, but I think the pod sucking in hot air, however little amount of air that is, is insignificant on a effectivley intercooled intake system...

-Jez

Valid point, but is the pod in that low pressure area "behind the rad"?

Im not saying your wrong but thinking about it I doubt that the air will get all that much kinetic energy transfered to it to keep the same momentum as the car (thus the pod) to allow a majority of it to be sucked in my the pod.

Sure the turbo will create a great amount of suction, but by the time it effects the area where the heated air that cooled down the rad is most of that air should be on its way out of the engine bay or be hit against the engine and bounce elsewhere, some to the pod and most of it elsewhere in the bay...

Eitherway I still am a air box fan, and believe even with a pod mostly cold air will be sucked in.

At the end of the day there is an intercooler to cool the intake air, and if it is a 30+ degree say its just stupid to use drive any performance car (especially turbo) at its full potential, but I think the pod sucking in hot air, however little amount of air that is, is insignificant on a effectivley intercooled intake system...

-Jez

There is no cold air in an engine bay, its damn scorching under there, anyhow i used to have my pod unshielded right up kissing the passenger headlight and it was terrible, performance was always up and down, so moved it into the bumper bar, and power is now much more reliable, at night its spectacular, i have a just jap front mount so cant use standard air box

So your saying that the WHOLE engine bay is a low pressure area...

So where do you think the hot air from the radiator goes? The air is sucked out the bottom after swirling all through the engine bay. Admittedly there is a small amount of air coming around the headlight, and a clever guy will fit a snorkel into the front bar to use a spare hole to force some cold air in but without a really well constructed chamber there wil be heaps of hot air sucked in. Calculate 2.5L running at 6000rpm + 14psi of forced induction (so double the previous number) and then calculate the number of engine bays at around 300L that is sucking through each minute. Start to get the idea?

It's not uncommon for ambient temps in the street car engine bay to get to over 70degC and when an exhaust is glowing dull red that is about 700degC.

On my track 25t I measured post turbo temps of over 75deg off an enclosed pod with a highflow running 14psi and 220rwkw. After the Hybrid Monster 800hp FMIC it had dropped to 28 deg on a 27deg day. Imagine if it had been sucking 70deg air in.

On the GTR33 the airbox has an extra inlet through the side of the bay inside the guard so it will run extra power, but I'm currently working on a simple mod for the GTS25t airbox to take in extra air through the top with a snorkel to draw what cool air can be had.

i used to run my pod down in the front bar, never had any issues, cept the pod got dirty quicker

certainly never had any issues with airflow at speed (that i noticed anyway)

now have pod back in engine bay, sealed off nicely

i believe the sucky sucky noises give me an extra 20rwkw (in my mind)

So where do you think the hot air from the radiator goes? The air is sucked out the bottom after swirling all through the engine bay. Admittedly there is a small amount of air coming around the headlight, and a clever guy will fit a snorkel into the front bar to use a spare hole to force some cold air in but without a really well constructed chamber there wil be heaps of hot air sucked in. Calculate 2.5L running at 6000rpm + 14psi of forced induction (so double the previous number) and then calculate the number of engine bays at around 300L that is sucking through each minute. Start to get the idea?

It's not uncommon for ambient temps in the street car engine bay to get to over 70degC and when an exhaust is glowing dull red that is about 700degC.

On my track 25t I measured post turbo temps of over 75deg off an enclosed pod with a highflow running 14psi and 220rwkw. After the Hybrid Monster 800hp FMIC it had dropped to 28 deg on a 27deg day. Imagine if it had been sucking 70deg air in.

On the GTR33 the airbox has an extra inlet through the side of the bay inside the guard so it will run extra power, but I'm currently working on a simple mod for the GTS25t airbox to take in extra air through the top with a snorkel to draw what cool air can be had.

I'II show u mine geoff in in a few days if I get the chance. I have mocked up a new snorkel to replace the stock one...the inlet will be much wider, nearly to the radiator cap. in addition the snorkle itself will be bigger to add some volume to the intake side. I was gonna make a new lid, but decided this was enough at this stage to keep it looking stock. But I new lid would be good also.

You don't believe so?

Compared to the air pressure on the nose of the car yes... the whole engine bay has a lower pressure.

I totally agree theres a significantly lower pressure compared to the nose of the car. Hence my theory on its momentum. My tired thoughts have been misconstrued. So never mind about me.

So where do you think the hot air from the radiator goes? The air is sucked out the bottom after swirling all through the engine bay. Admittedly there is a small amount of air coming around the headlight, and a clever guy will fit a snorkel into the front bar to use a spare hole to force some cold air in but without a really well constructed chamber there wil be heaps of hot air sucked in. Calculate 2.5L running at 6000rpm + 14psi of forced induction (so double the previous number) and then calculate the number of engine bays at around 300L that is sucking through each minute. Start to get the idea?

It's not uncommon for ambient temps in the street car engine bay to get to over 70degC and when an exhaust is glowing dull red that is about 700degC.

On my track 25t I measured post turbo temps of over 75deg off an enclosed pod with a highflow running 14psi and 220rwkw. After the Hybrid Monster 800hp FMIC it had dropped to 28 deg on a 27deg day. Imagine if it had been sucking 70deg air in.

On the GTR33 the airbox has an extra inlet through the side of the bay inside the guard so it will run extra power, but I'm currently working on a simple mod for the GTS25t airbox to take in extra air through the top with a snorkel to draw what cool air can be had.

Totally agree, running a good source of cold air will help, but as youve mentioned a good FMIC as I also mentioned will make more of a difference in the end.

Ne hoo...Looks like Ive had my ass handed to me.....so Ill shut up now.

Nah, you had some good thoughts there. They just needed to be followed through a bit more and the links would have made you see what happens so well done on that. Certainly not about handing anyone ass or any other piece of anatomy.

A good sized FMIC will make a difference but needs help. I remember my stock side mount on 12psi was seeing over 60degC on a 29deg day but I could get that down to 34 with the IC water spray on. As they say: "you can't polish a turd". :)

Like I said, 130am ramblings......ne hoo, Im thinking about getting some temp senders under the bonnet when my cars done and on the track, see whats happening under there, cous If I can fit the R32 airbox like I had perviously in my R31 with the new turbo and pipe work then I will, if not I have to settle for a pod :O

just for every1s info.

I ran more power up today and had an issue with the stock rubber intake hose from the airbox to the turbo. Essnetially under hi load the rubber would collapse...obviously the air box was restricting this too much.

I replaced the box with a pod for the run which sorted the issue.

So essentially what I deduced was the stock air box and snorkel simply couldn't supply enough air over 1bar or around 250rwkw. This is with a trust hi-flow pannel filter.

Pod filter...no dramas at all. Hmm...I could replace the rubber with a al intake pipe to force suction. I think a new lid or ported stock box and bigger snorkels is in order.

So there u go.

Actually,on the subject of the inlet hose,has anyone tried cable ties every 50mm around it?I think just by doing that it feels just a little harder to squash.Havn`t had any issues since.

just for every1s info.

I ran more power up today and had an issue with the stock rubber intake hose from the airbox to the turbo. Essnetially under hi load the rubber would collapse...obviously the air box was restricting this too much.

I replaced the box with a pod for the run which sorted the issue.

So essentially what I deduced was the stock air box and snorkel simply couldn't supply enough air over 1bar or around 250rwkw. This is with a trust hi-flow pannel filter.

Pod filter...no dramas at all. Hmm...I could replace the rubber with a al intake pipe to force suction. I think a new lid or ported stock box and bigger snorkels is in order.

So there u go.

Never thought of it that way, but did it make any less power with standard box in place?

just for every1s info.

I ran more power up today and had an issue with the stock rubber intake hose from the airbox to the turbo. Essnetially under hi load the rubber would collapse...obviously the air box was restricting this too much.

I replaced the box with a pod for the run which sorted the issue.

So essentially what I deduced was the stock air box and snorkel simply couldn't supply enough air over 1bar or around 250rwkw. This is with a trust hi-flow pannel filter.

Pod filter...no dramas at all. Hmm...I could replace the rubber with a al intake pipe to force suction. I think a new lid or ported stock box and bigger snorkels is in order.

So there u go.

Now what would be nice to see is how much power less (if any) it would make if you were to leave the stock air box and replace the afm -> turbo pipe.

OR.. If you were to open up the std box and feed a decent cai in to it.

But yes.. Any dyno sheets we can see a back to back? Would be interesting to see where it began sucking in.

i run panel filter on my GTR.. its better than pods.. just cause GTR has too much crap and generate far more heat than an RB25 would. street cars i mean. unless u cut and re route air to the LHS of the engine bay its pointless.

having said that my brother just put on a DRIFT pod on his GTT. it sounds harder. doesnt feel quicker than the airbox.. and gives a gay drone noise at 1500rpm.

we measured the surface arear of a Trust mushroom pod we have at home and it is larger than a panel filter. not to mention the equal distance between funnel and filter substance.. wher as a panel filter is flat and the closes point is the LHS of the panel filter. so u would have different pressure rates on the sides of the filters unlike a pod which is more even.. do u guys follow?

i would rather an ARC AIRbox than a pod or stock panel filter..

Now what would be nice to see is how much power less (if any) it would make if you were to leave the stock air box and replace the afm -> turbo pipe.

OR.. If you were to open up the std box and feed a decent cai in to it.

But yes.. Any dyno sheets we can see a back to back? Would be interesting to see where it began sucking in.

thats what I was gonna suggest, run a steel pipe to the box, Im going to try this on my new setup and see how it goes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...