Jump to content
SAU Community

Recommended Posts

Hi Gents,

Now that I have my shiney new Splitfire Coil Packs (Big Thanks to the guys at Kudos Motorsports) I need to fit them.

My current plugs are gapped at about 0.7-0.8mm.

What should I gap them too?

Would 1.0 - 1.1 be about right?

BASS OUT

Link to comment
https://www.sau.com.au/forums/topic/87888-plug-gaps-and-splitfires/
Share on other sites

If its any interest to anyone, i've tested my std gtst old coils and the new splitfires, and aside from the primary winding resistance being .6 ohms against the stock ones .7 ohms, the secondary coil current is the same as the stock old ones(1.4ma). Also the spark gap they will jump is also the same.......(18mm)

This was using a set frequency coil tester, around 50 - 60 hz odd...... for 9000 rpm the freq would be 75 hz, so pretty close. stock coil might drop off abit at high freq, but i dont think its as much as they seem to indicate.

Anyone else done testing to argue otherwise ?

Gary

If its any interest to anyone, i've tested my std gtst old coils and the new splitfires, and aside from the primary winding resistance being .6 ohms against the stock ones .7 ohms,  the secondary coil current is the same as the stock old ones(1.4ma).  Also the spark gap they will jump is also the same.......(18mm)

This was using a set frequency coil tester, around 50 - 60 hz odd...... for 9000 rpm the freq would be 75 hz,  so pretty close.  stock coil might drop off abit at high freq, but i dont think its as much as they seem to indicate.

Anyone else done testing to argue otherwise ?

Gary

I don't even know what you're on about, how can I argue? :lol:

They only reason they "seem" much better is a lot of people buy those as opposed to ones off Nissan which probably is more expensive.

I dont think they are any different to stockers... its just that they are a cheaper brand new alternative

A Brand new coil pack is going to be better than one that is 5/10/15 years old

Yeah that was my asumption too, there just a blue version of a new coil basically...... there are minor diferences in the primary resistance, and also the core seems to be two E cores instead of all joined together. (ie the metal former is not joined on the sides)

I assumed this when buying them, but since there new and cheaper than nissan, there the ones to get.

I would think all the guys who report more power have old coils starting to break down internally , and worst case externally arcing onto the coil brackets.

Only way i'd believe these are better is run a car on brand new nissan ones till it was blowing the spark out at a certain gap, then swap these in.... but i doubt there would be any gain on new coils.

For interests sake i also tested the secondary current of some other coils .

gtst - 1.4ma

bosch mec 718 2.1ma

S4 rx7 trailing 2.9 ma !

Gary

I would think all the guys who report more power have old coils starting to break down internally , and worst case externally  arcing onto the coil brackets.

Thats exactly what ive been thinking for along time ;)

my coils started arcing to the brackets (at least three of them) and as has been mentioned i bought the splitfires because they were cheaper than nissan ones. they look exactly the same, and i can tell you that there was definetly NO power increase when compared to my stock coils when they were working properly ;)

and talking gaps, with my splitfires i have run both coppers and iridiums with the standard 1.1 gap with no problem, but only at 10psi.

Wow I thought we were gettin extra juice outta these Splitfires.... Ripped off!! Just like thier friggin spark plugs..

well talking plugs, i swapped old (40,000kms 2.5year) iridium ix plugs which looked fine for new coppers, no difference. i only changed them because they were old...

i believe the standard coils in conjunction with being old somehow get damaged inside after being exposed to a lot of heat.

mine started arcing all of a sudden, within days after i went to a skidpan day(refer to picture ;) ), lots of sustained high revs, and it was a very hot day

  • 2 weeks later...

I found a 10psi 1.1 mm gap was fine on irudiums

but

at 14psi it was blowing out spark.... If i reduce the gap to 0.8 then i get a small flat spot where there is too much fuel and its drowning the spark bsiclly.... So im gonna toss out the split fires and run after market coil packs and spark plug leads....

Should reduce the heat issues these things have also....

$600 for a set of split fires.....

vs.

$400 for a set of 3 double packs from bosch and $100 on a set of leads from autobarn....

Much the same price but i know which will do a better job....

Remember this one basic rule....

If you want more power you need...

1. More fuel (040 fuel pump and bigger injectors and maby a fpr)

2. More air (turn up the boost)

3. More ignightion (bigger plug gaps and more power for the spark)

If you dont increase each evenlly you will have trouble....

i got 3rwkw increase on back to back dyno runs just by changing to the splitfire coils, which im not claiming is reason to go out and buy em! my std ones were getting temperamental.

Plug gap had to remain at 0.7mm otherwise id get missfires at 1.2bar.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
    • Add more solar panels to the array. Call the electricity company and tell them you're moving out... Live off grid electric wise
    • Hi Jasmine. How's the war going?
    • I'm extremely suspicious of the VPP stuff. Best I can tell, you surrender any and all control of your panels and battery to the VPP, because there's no way that anyone could write a sufficiently useful set of "rules" as to how much you would be willing to let out of your export meter at any given time. If one of your main interests is to have enough in your battery every evening to get you through the night without having to import, you could easily find yourself with nothing in your battery at the end of the day, or part way through the night, and then be paying import pricing instead of paying nothing. I cannot see how this cannot come to pass.
×
×
  • Create New...