Jump to content
SAU Community

Recommended Posts

FOLLOWING PARTS ARE AVAILABLE OFF R32 GTE 4-Door

PRICES ARE NEGOTIABLE - ESPECIALLY ON BULK PURCHASES

Doors - $150ea

Door Glass - $50ea

Electric Window Regulators - $75ea

OR Complete Doors - $220

Other Door Window Controls - $25ea

Automatic Console - $100

Glove Box - $80

Front Seats - $150/pr

Rear Seat - $100

Complete Lock Set (Ignition,Doors,Boot) - $100

Steering Column & Standard Steering Wheel - $75

"A" Pillar Trims - $25ea

"B" Pillar Trims (Upper and Lower) $50 a side

Carpet - $50

Front Courtest Light - $50

Rear View Mirror - $20

Side Mirrors - $50ea

Scuff Plates - $60/set

Kick Panel Trims - $10 ea

[/b]

Brake Pedal Assy - $40

Coil Packs and Coil Pack Loom - $200

Dashboard - $75

Fuel Pump - $50

Accelerator Pedal Assy - $40

Radiator - $110

Wiper Motor - $40

Overflow Bottle - $25

Windscreen Washer Bottle $25

RB20DE Ecu - $40

Tailshaft - $50

Front Bumper Bar Reinforcement - $100

Front Bumper Bar - $100

Bonnet - $150

Front Guards - $80 Ea

Head Lights - $145 Ea

LH Tail-Light - 4-Door - $150

GT Guard Badges - $15 ea

CA Silvia Rims - $150/set

2.5" Cat Back Exhaust W/- Cannon - Almost New - $300

Other Parts Available, Please Enquire

Edited by homlie
Link to comment
https://www.sau.com.au/forums/topic/88128-r32-parts/
Share on other sites

  • Replies 86
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...