Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Hello Boostor, but I am going now. After an hour of messing about with the computer, finally getting on the site, I have to leave. Have a good weekend, I will be working night shift.

Should get some of the boys to come down and rev their engines infront of the nursing home at around 2am.

Originally posted by macka

Juha Kankenin (spelling) is down for it??

and racing his new mitsubishi prototype apparently

Gees , it's quiet in here tonight ?

Macka you knoob , it Juha Kangas in a Mitsubishi evo 7 running under the Les Walkden banner from Tasmania.

Juha Kankunnen is an ex WRC Hyundai driver who wouldn't and couldn't come over here for anything less than Rally Oz.

If your coming down , cruise out to the real rally stages on Saturday and Sunday were the Rally is based around Nannup.

Will be there looking after 5 cars for Maximum Motorsport.

Cheers

Ken

Originally posted by GTS-t VSPEC

Hi Ken,

I seem to be having troubles with this thread, are you?

See'ya:burnout:

why , cos of the amount of booze you consumed with Macka ?

Nope , works fine for me.

Cheers

ken

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...