Jump to content
SAU Community

Whoretown WA

skyzerr33

By skyzerr33,
in Western Australia

 Share

Recommended Posts

Pva_Glue Grand Master

Pva_Glue

Posted
Posted
Originally posted by darK

yea.. i was kiddin with the "kun"..

yea.. i know he's korean.. i was trying to speak german.. but i forgot it all ;)

lol

hahahah good try...

should say more like "An nyoung Ha Sae Yo!" :)

and also "kun" or "con" in Koean means Sir ;):(

Jap and Korean have similar sound words :(

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Popular Days

Top Posters In This Topic

Popular Days

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by macka

Mike dont wreck your car u only just got it going properly!!

I agree , don't **** with it until you are going to do some wholesale changes like aftermarket terbs etc.

Remember the ones at the track have no aircond , don't have to idle well , are running no airflow meters , hence no recirculating BOV's ... etc etc.

cheers

Ken

Nizmo Grand Master

Nizmo

Posted
Posted
Originally posted by gtrken

Remember the ones at the track have no aircond , don't have to idle well , are running no airflow meters , hence no recirculating BOV's ... etc etc.

cheers

Ken

Sounds like my car :(

Micko Veteran

Micko

Posted
Posted
Originally posted by gtrken

I agree , don't **** with it until you are going to do some wholesale changes like aftermarket terbs etc.

Remember the ones at the track have no aircond , don't have to idle well , are running no airflow meters , hence no recirculating BOV's ... etc etc.

cheers

Ken

Hmmm...once again the voice of reason rings loud in my ears.

Thanks Ken - just want a clean looking engine bay & less pipework so that I have a chance of understanding what is going to what:uh-huh:

gtrken Grand Master

gtrken

Posted
Posted
Originally posted by Nizmo

*sigh* but front and rear have been swapped I watched them do it!

Ahh yes , I know that , you told me last night. ( remember , I stalk you Niz and hang of every word you say.... )

Did the problem get worse after they swapped them and why did they swap them in the first place.

I am not having a go at you but as I also mentioned last night , one of the major probs with doing correct diagnosis is knowing ALL the symptoms and what was happening leading up to the prob.

cheers

Ken

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Kinkstaah
      NC MX5

      By Kinkstaah · Posted

      I am well aware as I did rant at him to buy a MX5, buy the 2.5 before he DIY'ed it, etc as well as do things to the holden. He will obtain a ND. It's the best of both worlds. They look great in person, definitely the best looking one. Just a matter of time now.
    • r32-25t
      NC MX5

      By r32-25t · Posted

      Remember this is the same person who said he’d never own an nc 
    • zique
      Ceramic turbine damage to engine - what did yours do?

      By zique · Posted

      ouch! how is the car now?I had sold my gtr but have been looking into some on trademe and a 260RS but I wouldnt be keen on any repairs needed on them
    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
×
×
  • Create New...