Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Originally posted by Micko

Dont you guys like my taste in music or something?

You must be jealous of my vocal skills:bahaha:

Nothing wrong with the Boss and the Eagles.

Just your rendition of the songs leaves a bit to be desired I am told.:D

Cheers

Ken

Originally posted by 33Spec2

hello niz

aaaaw the picture is gone!:D

vicki its russell lets see if you remember next time i ask you:D

Russell , you must have been the only one to see it.

Bloody too quick these mod guys...

Cheers

Ken

Fair enough - I am a shocking singer - only did it to entertain the crowd...

Hey Ken - ever since I changed the front pipes the fuel consumption has gone through the roof. Is this due to the bit of extra boost being made or would it just be because my foot has been welded to the floor 'testing' the new pipes?

Originally posted by Nizmo

hi russ n micko

Know how u feel Kyles - if it wasnt for the money im earning i would be outta my job as well - just one too many lazy bitchy dickheads there

Found out a long time ago , money isn't everything and lifes too short to be doing shit you don't like.

If you are prepared to have a go and not be afraid of the unknown , then quit .

Cheers

Ken

Originally posted by Micko

Fair enough - I am a shocking singer - only did it to entertain the crowd...

Hey Ken - ever since I changed the front pipes the fuel consumption has gone through the roof. Is this due to the bit of extra boost being made or would it just be because my foot has been welded to the floor 'testing' the new pipes?

prolly the latter.

Have you got the mines puter in ?

Cheers

Ken

its just not nice going to work atm, I got a written warning today for some things i didnt even do. And I have to take some time off coming up beacuse of medical stuff and she was really unreasoable and really not understanding or supportive at all... And everyone else seems to have no problems getting time off for medical appiotments or things like that atm .. but im made to feel bad about it when i ask. Not my fault.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...