Jump to content
SAU Community

Recommended Posts

  • Replies 103.8k
  • Created
  • Last Reply

Top Posters In This Topic

  • GTS-t VSPEC

    20904

  • Nizmo

    13582

  • SHUTO-BOY

    6636

  • skyzerr33

    5353

Sill little kids harrassing me in shopping centre carpark today ...... its like a new generation of mikey's waiting to happen!! "Wow you drive the most awesome car" .... little brat with bike a little too close to my paintwork .... "See that car over there" ...points to dodgy faded green R30 ... "thats a Skyline too" .... "but yours is the best" ...... that was all cool until that started hassling me for change ...."with a car like that you have to have some kinda change" ......me:"Look kid when you get older and you own a car like this - you'll no why i dont have any change!!"

Why do i always get blame for everything :confused:

i'm bright ****ing red.

*mental note to self* put sunscreen on BEFORE you go visit your g/f's horses in whoop whoop when there is no shade*

At least I had fun tormenting LOTS of ants. Found some MASSIVE nests and just annoyed the **** out of them.

Think I'll take a magnifying glass next time :mad:

LOL i do that - we have bees that fall into our pool ..... and so if you take them out an dput them on pavement they just fly into pool again :mad: so i take them out n put them on an ant nest nearby and watch all these little ants attack the bee.

I reckon I had about 2000 ants at the first nest, and I would stick a stick down their main hole, you'd get another 1000 ants come straight out and form like a manhole cover over the hole and about 100 ants climb up the stick and attack it, then I pissed on them and a heap died, it was cool.

The second nest started off with about 10 bullants and I poked the hole and another 50 or so came out, then I fully mashed it up and about 200 came out, so I pissed on them and some of them died too.

Bet you've never done THAT niz :mad:

I'd hate to be a chick (except you'd get to do all kinds of cool things to yourself) and have to piss over an ants nest, cause you'd have to squat RIGHT over it .. At least I can stand back and laugh and not have the little buggers crawl up my feet/legs :mad:

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...