Jump to content
SAU Community

Take A Look At This Headunit...

AMS

By AMS,
in Car Audio & Electrical

 Share

Recommended Posts

someonestolecc Grand Master

someonestolecc

Posted
Posted

Looks like a cd player... the bottom one is a controller (as it says in the photo) and the top one is the a normal cd player.

What exactly do you need to know? From the picture I would assume there's a cd stacker floating around in the car somewhere too (hopefully still here when you get the car).

On the upside you might get away with being able to keep the bottom HU to control the stacker if you decide to get a new aussie spec HU..

AMS Grand Master

AMS

Posted
  • Author
Posted

The stacker is in the boot

WGNC34-01070016.jpg

I wanted to know if anyon had this headunit, because I have been offered a pretty good deal on some brand new Pioneer headunits. I wanted to know the specs of these units to see whether they will be sufficient for my audio. I wanted to know whether to change it or not...

funkymonkey Grand Master

funkymonkey

Posted
Posted

you'll need a band expander (unless you like listening to christian radio all the time because that's all you pick up with japanese radios), other than that cd etc should be just fine.

dezz Grand Master

dezz

Posted
Posted
The stacker is in the boot

WGNC34-01070016.jpg

I wanted to know if anyon had this headunit, because I have been offered a pretty good deal on some brand new Pioneer headunits. I wanted to know the specs of these units to see whether they will be sufficient for my audio. I wanted to know whether to change it or not...

i'd be taking those deals and replacing it....

not only is it ugly imo, but its old, and extremely out dated now

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...