Jump to content
SAU Community

Recommended Posts

  • Replies 625
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

It's gonna be another BEAUTIFUL day..

Put the car in for a service today..

and finally got the bleed valve installed.. oh yeah baby.. oh yeah!

Alien.. you trying to Jinx it :rolleyes:.. we can always change @ thornleigh maccas.. I don't mind..

Stan - did you have a charger for the radio, or did it come with a serperate one?

Edited by Links
Menthu sorry didn't see your post up there before.

I was thinking this Uniden one.

http://www.dse.com.au/cgi-bin/dse.storefro...duct/View/D1804

Yeah that pack looks good...!

I wouldn't mind the one with backlit LCD and rechargeable batteries tho... it's a bit more expensive... and then we'd have the problem of who would get the charger? :)

0.7W Rechargeable Pack

I'll have a think about the pack you said - suppose the batteries don't matter that much. I could buy it tomorrow and give you your one on the cruise? :rolleyes:

Stop saying it's going to rain....  IT'S NOT GOING TO RAIN!!!

hey stan-dard... i don't want to take my car, nobody to talk to, have no money for fuel (well, i do - but then i wont be able to get the rails for my recaros next week!) and also most importantly - my tyres are seriously dodgy (i bought them just to use for rego, lol)... i don't reckon i could go down the old pac without understeering off a cliff :lol:

annnnnd i wanna see how your car goes around the twisties... so can i shotgun your passenger seat again? :rolleyes: will put in a bit for fuel... and bring lots of trance B)

The CB that I got off N1GTR runs off 3 AAAs - no charger involved :rolleyes:

And Luke; yeah you can shotgun my passenger seat - those two items sound good :) You'll just have to figure out how you're going to get to my area in the morning - I sure as hell will not drive to pick you up ;)

Well..I think i'll probably just get the 2 x Battery powered ones that don't need the charger.. that way don't have to worry about chargers..

The more the merrier.. someone has to take me for a spin in their GT-R.. and stan.. you owe me a ride in your car..

Hi folks... I've just received my silver 33 SII last week, after 2 months of compliance headaches.

Got some new rims 4 it today after rolling on 205's. (scary in the wet).

I hope noone minds if i tag along for a while on the cruise, but i have to be back in the city by 1pm so i'll peel off at gosford.

I'm all excited.... my first cruise :D

Hi folks...  I've just received my silver 33 SII last week, after 2 months of compliance headaches.

Got some new rims 4 it today after rolling on 205's. (scary in the wet).

I hope noone minds if i tag along for a while on the cruise, but i have to be back in the city by 1pm so i'll peel off at gosford.

I'm all excited....  my first cruise  :angry:

urgh sounds like one bit compliance headache

come along, will be a great day!!!

see you sunday!




  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...