Jump to content
SAU Community

Recommended Posts

Hi All,

Just a reminder that Drag Wars is on this weekend, so make sure to get down and support the event, either by entering or spectating. This is the last dedicated high-tech event for the year, so make sure you come on down. Details below.

Cheers

Paul

After a successful return to Quit Motorplex last season the popular Street meet for Vehicles powered by 4 cylinder , 6 cylinder and Rotary powerplants returns on Saturday night October 15. A fully prepared track awaits the 140+ Hi Tech racers who will converge on the Quit Motorplex for a bit of quarter mile action with some great trophies and prizes up for grabs!

There are classes for:

.: AWD - All Motor All Wheel Drive

.: FAWD - Forced Induction All Wheel Drive

.: RWD - All Motor Rear Wheel Drive

.: ANDRA Sport RWD - Forced Induction Rear Wheel Drive - Download Regs Here

.: FWD - All Motor Front Wheel Drive

.: ANDRA Sport FWD - Forced Induction Front Wheel Drive - Download Regs Here

* Forced Induction = Turbocharging, Supercharging or Nitrous Oxide

.: EXTREME - ANDRA 4,6 & Rotary Group Two and Three race vehicles

Note - Depending on entry numbers on the day some brackets may be combined.

There will be trophies and prizes for the quickest time recorded in each of the categories plus trophies and prizes for the winners and runners up in each of the brackets.

Handicapping will be the Dial Your Own (DYO) index system which means anyone can win!

This is definately one of the great Hi Tech events of the season and chance for everyone to blow the cob webs out after the winter break.

There will also be a burnout competition with great trophies and prizes for the winner and runner up.

So mark Saturday night October 15 in your calendar for the annual Hankook Performance Tyres 4+6+Rotary Drag Wars - and remember - "If ya have an eight...leave it at the gate!"

Additional event information can be obtained by contacting the Quit Motorplex office on 9419 6622.

Competitor Entry 1:00pm

Spectator Entry  3:00pm

Racing

- Qualifying        3:00pm - 6:00pm

- Eliminations      6:30pm - 8:30pm

- Burnout competition    8:35pm approx

- Finals              9:00pm

Competitors 

Non ANDRA Licence Holders $40.00

ANDRA Licence Holders $35.00

Spectators 

Adults $18.00

Concession (proof required) $16.00

Children (5-15yrs) $8.00

Children (under 5) FREE

Family (2+3) $44.00

Go to www.motorplex.com.au click on the Hankoon 4,6, Rotory dragwars under events and you'll see a pic of my car :) hehe

I won't be there unfortunately ;) I have a family function on that day.

Has anyone seen any advertising for this event, either on TV, radio, newspapers or flyers? Just wondering how much promotion is being given to Hi-tech events.

pauly, the 1st i heard about the event was here in this thread, i would have made an effort to have my car ready if i knew there was a drag event coming up

I actually heard on the radio last night at the gym, but still think there is a severe lack of promotion of this event. Hopefully we can improve that in the future.

The government wouldn't be happy with that though, having publicised nights dedicated to this sort of thing. It would mean less cars to impound, and less stories for the news about all those young hoons in high performance cars. Today Tonight will be feeding on scraps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...