Jump to content
SAU Community

Recommended Posts

Ok here is the problem, i have no power above 2500 revs, it will go up to here fine then once it hits that point then it will just stop like it is not getting any pertol. When it is doing this problem it will idle at about 1500 - 2000 revs instead of 500 - 1000 revs. Now this does not happen every time i drive the car and there is no common pattern that makes it do it.

I have had the car services and the mechanics cleaned out the injectors, put a new fuel pump in, checked the fuel pump, changed spark plugs and a heap of other things and could not find anything that is making the problem.

The car is a r32 gts-t (rb20det) with a 3" exausht from turbo and a 5" tip, and a HKS pod filter. Any help would be great as it is making the car so hard to drive.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/
Share on other sites

The 5" tip is your problem - too much bling for a R32 GTSt.

Seriously, though, if you searched these forums you would have been able to uncover that fact that a dead or dying AFM (Air Flow Meter) will set the ECU into limp-home mode and will not permit the engine to rev at more than 2500.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1633914
Share on other sites

my bad its only 4"

Hehe, in that case maybe you need it upgraded to 5" ;)

Seriously though, it's almost certainly an AFM problem. I've had a similar thing happen when I accidentally yoinked out my S-AFC awhile ago, which among other things, severs the signal wire from the AFM. I also recently have my AFM die a half-arsed death, which resulted in the car being unable to idle, although I could get above 2500rpm in that case by keeping the throttle open.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634188
Share on other sites

Why not just run an ecu diagnostic rather than playing guessing games to see what your problem is? That will give you a definative answer to if your car has a bung AFM. Idling problems can be caused by an excessive amount of things just to name a few dirty/in-op/incorrectly set AAC valve, incorrectly set idle via throttle plate, carbon buildup on throttle plate, AFM problems, air regulator and the list goes on....

Do a seach and that should fix your problem.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634265
Share on other sites

Second hand should be around $150 or less. Try Ebay, you might be lucky. If not then JustJap should have one and they deliver too. Test it before you go and buy one first, it could just be a bad connector or something. See if you can borrow a known working one from someone and hook it up.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634395
Share on other sites

Going to the mechanics tomorrow to have it hooked up to a diagnostics computer. Hopefully it is just a bad connector as this will take away money from my FMIC ;)

What would cause it to go into limp-home mode, as it doesnt always have the problem?

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634419
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To expand on this to help understanding... The bigger/longer the block is, the more it's going to work to sit on your far away high areas, and not touch the low stuff in the middle. When you throw the guide coat, and give it a quick go with a big block, guide coat will disappear in the high spots. If those high spots are in the correct position where the panel should be, stop sanding, and fill the low spots. However, using a small block, you "fall off" one of the high spots, and now your sanding the "side of the hill". Your little block would have been great for the stone chips, where you only use a very small amount of filler, so you're sanding and area let's say the size of a 5/10cent piece, with something that is 75*150. For the big panel, go bigger!   And now I'll go back to my "body work sucks, it takes too much patience, and I don't have it" PS, I thought your picture with coloured circles was an ultra sound... That's after my brain thought you were trying to make a dick and balls drawing...
    • Oh I probably didn't speak enough about the small sanding block for blocking large areas.  In the video about 3 minutes in, he talks about creating valleys in the panel. This is the issue with using a small sanding block for a large area, it's way too easy to create the valleys he is talking about. With a large block its much easier to create a nice flat surface.  Hard to explain but in practice you'll notice the difference straight away using the large block. 
    • Yep I guessed as much. You'll find life much easier with a large block something like this -  https://wholesalepaint.com.au/products/dura-block-long-hook-loop-sanding-block-100-eva-rubber-af4437 This is a good demo video of something like this in use -    You have turned your small rock chip holes into large low spots. You'll need to fill and block these low spots.  It's always a little hard not seeing it in person, but yes I would go ahead and lay filler over the whole area. Have a good look at the video I linked, it's a very good example of all the things you're doing. They went to bare metal, they are using guide coat, they are doing a skim coat with the filler and blocking it back. If what you're doing doesn't look like what they are doing, that's a big hint for you  
    • The odometer does go up when driving.  Does this tell it is an issue with the speedometer itself?    Where can I look for replacement cluster? Or speedo? I can likely do the repair.. Will ER34 cluster work on HR34? Or do I need a HR34 20GT S2 specifically lol   
×
×
  • Create New...