Jump to content
SAU Community

Recommended Posts

Ok here is the problem, i have no power above 2500 revs, it will go up to here fine then once it hits that point then it will just stop like it is not getting any pertol. When it is doing this problem it will idle at about 1500 - 2000 revs instead of 500 - 1000 revs. Now this does not happen every time i drive the car and there is no common pattern that makes it do it.

I have had the car services and the mechanics cleaned out the injectors, put a new fuel pump in, checked the fuel pump, changed spark plugs and a heap of other things and could not find anything that is making the problem.

The car is a r32 gts-t (rb20det) with a 3" exausht from turbo and a 5" tip, and a HKS pod filter. Any help would be great as it is making the car so hard to drive.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/
Share on other sites

The 5" tip is your problem - too much bling for a R32 GTSt.

Seriously, though, if you searched these forums you would have been able to uncover that fact that a dead or dying AFM (Air Flow Meter) will set the ECU into limp-home mode and will not permit the engine to rev at more than 2500.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1633914
Share on other sites

my bad its only 4"

Hehe, in that case maybe you need it upgraded to 5" ;)

Seriously though, it's almost certainly an AFM problem. I've had a similar thing happen when I accidentally yoinked out my S-AFC awhile ago, which among other things, severs the signal wire from the AFM. I also recently have my AFM die a half-arsed death, which resulted in the car being unable to idle, although I could get above 2500rpm in that case by keeping the throttle open.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634188
Share on other sites

Why not just run an ecu diagnostic rather than playing guessing games to see what your problem is? That will give you a definative answer to if your car has a bung AFM. Idling problems can be caused by an excessive amount of things just to name a few dirty/in-op/incorrectly set AAC valve, incorrectly set idle via throttle plate, carbon buildup on throttle plate, AFM problems, air regulator and the list goes on....

Do a seach and that should fix your problem.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634265
Share on other sites

Second hand should be around $150 or less. Try Ebay, you might be lucky. If not then JustJap should have one and they deliver too. Test it before you go and buy one first, it could just be a bad connector or something. See if you can borrow a known working one from someone and hook it up.

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634395
Share on other sites

Going to the mechanics tomorrow to have it hooked up to a diagnostics computer. Hopefully it is just a bad connector as this will take away money from my FMIC ;)

What would cause it to go into limp-home mode, as it doesnt always have the problem?

Link to comment
https://www.sau.com.au/forums/topic/90708-annoying-problem/#findComment-1634419
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...