Jump to content
SAU Community

Recommended Posts

depends, do u like driving a manual do you think they can be annoying in traffic ? or would u rather just whack it in drive and be on your mary way ???

its personal choice, drive both, see what u prefer and go from there. I prefer manual cars as i beleive u have a little more control over them, how they react etc ...

oh and they are just more fun

im deciding on a r34, wat should i buy?

the auto or manual...

manual seem to be heaps difference, dunno its very hard to decide, need ur guy's opinions

Manual.

As above, more fun, feels like you have more control and better resale value.

Also, buy a car already, your questions are getting annoying..... :O

people buy auto's for proper drags though i think thats bs unless u r building a proper off street drag car

dude go for the manual, a lot more fun and more control of your revs. i drive a manual car everyday and i never get sick of it even in peak hour traffic and then i drive my mums auto VT and it just sucks balls and doesnt respond aswell

im deciding on a r34, wat should i buy?

the auto or manual...

manual seem to be heaps difference, dunno its very hard to decide, need ur guy's opinions

i`ve been buying R34`s last couple of months and come to this conclusion,if you MUST have a manual..be prepared for 4-5k difference and don`t get fussy on colour etc.there is 10 or more auto`s available for every manual,most are in better condition ,lower milage etc..all my cars are manuals...but everytime i visit sydney...50 sets of traffic lights from hornsby to camden..i`m over the whole clutch thing pretty quick

Manual for sure mate.

Youll save having to change your brake pads as often with downshifting to slow down & lower your speed, although you'll have the clutch to worry about. But providing to you dont treat the clutch like a ratbag you should have no problems with it slipping for quite a long time... the standard clutch in my R33 lasted 114,000K's, providing that i bought the car with 70,000 on the odometer. Was a beauty of an excuse to chuck a ceramic 6 puck X-tremer in!

Then again, you're gonna own a turbo skyline, manual... > who wouldnt treat it like a ratbag :-D

I have an auto R34.

I can control when shifts occur, I can downshift coming to traffic lights.

It's called tiptronic, once you get used to it the steering wheel shifts it

becomes second nature. Not as fast as manual at shifting but much better

than standard auto.

Not trying to say that its better than manual cos it isn't. But tiptronic does

provide me with the ability to chose when i change up or down gears.

It's also good having the choice to swing into standard auto when in

traffic.

This and the fact that I paid $6k less than the same car in a manual, and

that I got one in possibly better condition for that $6k less, keeps me

happy with my choice.

Test drive both.

I have an auto R34.

I can control when shifts occur, I can downshift coming to traffic lights.

It's called tiptronic, once you get used to it the steering wheel shifts it

becomes second nature. Not as fast as manual at shifting but much better

than standard auto.

Not trying to say that its better than manual cos it isn't. But tiptronic does

provide me with the ability to chose when i change up or down gears.

It's also good having the choice to swing into standard auto when in

traffic.

This and the fact that I paid $6k less than the same car in a manual, and

that I got one in possibly better condition for that $6k less, keeps me

happy with my choice.

Test drive both.

well said ...tiptronic is a good compromise..and the 6k thing is spot on

I am also going to say that tiptronic auto is not that bad for an R34, having one myself I have not been disappointed yet. Sure the arguement lies that manuals get more power, control and 'fun' but I think the tiptronic is not very far off.

The shifting arguement is void with tiptronics as they can do pretty much the same thing - except launches. I guess an extra bonus to tiptronic is that they can downshift a hell of a lot faster than manuals.

As zymotic said, it's bliss knowing that you can choose between lazy mode and semi lazy mode! Comes in handy when the girlfriend is there :(

Heel-toe isn't needed in today's cars.

But it keeps the car well balanced when changing gears + breaking.

Most useful when entering a corner.

Smart ass? I think you took it wrong way.

It's just another advantage of a manual.

Better beef up your auto boxes if you're gonna be chasing power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...