Jump to content
SAU Community

Recommended Posts

Well I have decided to sell the R33 at the end of the year, because I'll be looking to buy a house.

Just letting everyone know in advance, incase they are after parts, I will be taking the car back to stock as modded cars are too hard to sell for what they are worth.

Parts that will be available are as follows:

Z32 AFM & Plug

HKS GTRS Turbo

Nismo 550cc Injectors

3" JJR Bellmouth Front/Dump pipe

Kakimoto Regu 06&R Cat Back

Apexi PowerFC with Commander and Electronic Boost Controller

Splitfire Coilpacks

Nismo Fuel Pump

Cold Air Box

HICAS Lockbar

Will post up closer to these parts being available. Just giving a heads up, as I know what it's like when you buy brand new parts and the next week good second hand parts become available.

Start saving! :down:

  • 2 weeks later...

31's driveable and seeing the odd short trip, lots of little jobs left though. Like paint/fit front bar, lip, roll and paint both rear quarters and paint both front guards; pull leaking front pipe off and get welded up ('perfect condition' secondhand BATMBL dump I bought for a fair amount of dough leaked from the word go around the wastegate pipe...), wheel align, solid subframe and diff mounts, and proper tune.

But it goes, skids and sounds angry, haha.

31's driveable and seeing the odd short trip, lots of little jobs left though. Like paint/fit front bar, lip, roll and paint both rear quarters and paint both front guards; pull leaking front pipe off and get welded up ('perfect condition' secondhand BATMBL dump I bought for a fair amount of dough leaked from the word go around the wastegate pipe...), wheel align, solid subframe and diff mounts, and proper tune.

But it goes, skids and sounds angry, haha.

SO in other words look out the streets of Hobart :)

Picked up my new 040 from SPG last week so all that leaves is tuning of the blue bucket :)

Well, rear subframe bushes let go, ordered some new ones but got sent wrong ones.

Made some phonecalls and was told Nolathane were outta stock till mid July. Now I am told its mid August...

So I decided to pull the front end apart and replace the LHF Inner Driveshaft boot. Easy enough job, except nobody has a boot that fits... Spose my local Nissan dealer will tell me they are about $90 each and 4 weeks outta Japan next for a genuine one.

So the GTR is sitten on stands with bits missing everywhere and the Baskerville Hillclimb is on in three weeks. This will be pushin it to get everything here and done by then.

Dude that is F'n harsh!

What about the RB25 thats for sale??

Didn't want to go RB25 as none of my parts (cams, gears, injectors etc) would fit, would need a new ecu and turbo not ideal either.

Well, rear subframe bushes let go, ordered some new ones but got sent wrong ones.

Made some phonecalls and was told Nolathane were outta stock till mid July. Now I am told its mid August...

So I decided to pull the front end apart and replace the LHF Inner Driveshaft boot. Easy enough job, except nobody has a boot that fits... Spose my local Nissan dealer will tell me they are about $90 each and 4 weeks outta Japan next for a genuine one.

So the GTR is sitten on stands with bits missing everywhere and the Baskerville Hillclimb is on in three weeks. This will be pushin it to get everything here and done by then.

I know the feeling, i order some gear for the FC from Rare Spares and they sent me the wrong items, when i rang to let them know they informed me that they didn't have what i needed instock and that it would be 12 weeks before they would have what i needed :rolleyes:

well, my mate fixed my powerfc so kermit is back in action! hoping to enter basky hillclimb too which should be fun :)

Glad to hear its all sorted, lets hope nothing else happens now :bunny:

Well thankfully I managed to fit the aftermarket boot to the driveshaft. Looks like it will work for now.

So as long as I can either get the bushes from Nolathane or temp up some "pineapples" I should be good for the Basky Hillclimb yet again.

Well thankfully I managed to fit the aftermarket boot to the driveshaft. Looks like it will work for now.

So as long as I can either get the bushes from Nolathane or temp up some "pineapples" I should be good for the Basky Hillclimb yet again.

The race is on, i have to remove old engine and put on stand to remove cams, injectors, gears and covers. Tidy up engine bay whilst its out and then when new engine arrives fit cams, injectors, gears and covers before dropping that back in.

Have to fit 040, new seat/harness and harness tabs and then tune it so i can make the hill climb :(

Racin before the event and all... thats competitive.

Well I just selected another gear, bush kit arrived and was the correct one this time.

Just arranged shed space, as mine is full at the moment, for this Saturday to fit em all up.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Oh, also, forgot to add these photos I believe.
    • Thought i'd update on this. I was able to get in contact with Craig Lieberman and later on Darryl Alison (owner of Kaizo Industries). Darryl was able to help me verify that my car was in fact one of theirs and is helping me find more info on mine !
    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
×
×
  • Create New...