Jump to content
SAU Community

Recommended Posts

i replaced mine at about 80k, when it was all still stock

was coming back from nimbin to the tweed (awesome drive by the way)

could smell clutch burning most of the trip

got back to brisso and it started slipping in 3rd and 4th going up hills

replaced with exedy heavy duty clutch for 500 bux or so and havent had a drama since

YES,

REVING-BUT NOT GOING ANYWHERE WOULD BE A GOOD SIGN.

SMELL-IS ANOTHER THAT YOU ARE BURNING THE CLUTCH.

My stock clutch seemed to be on it's way out showing these kind of symptoms.Then i added more 25rwkw more power took it to the drags,it couldnt handle the power and just slipped off the line.then in second so i gave up going for third.

At the moment the 5 puck ceramic HD clutch is great,though,i havent driven it more than 500klms in a year.

was driving my car one night and just put my foot down to over take someone and it started slipping. could smell some nice clutch smoke. so thats how mine went. just couldnt handle it any more.

when we replaced it we had a look at it and it was well and truely screwed (lived a pretty hard life)

it was replaced with an exedy etra heavy duty twin plate clutch and has been sweet ever since. :):)

heheh well i only recently got the car.. NO mods except catback.. n the stock clutch slips in 4th n 5th..

But i have bought a heavy duty excedy clutch to go in there..

Seems like everyone is replacin stock clutch with excedy clutch.. hehe guess i did the right move n bought it for the best price ever (320-from C & B)

Edit: 78000ks.. im sure the clutch started slippin in japan probably a thousand or so ks b4..

Edited by siddr20

I paid $680 for an excede sports tuff clutch fitted here in canberra, it started to die around a year or so ago, you could tell because its friction point kept getting less and less.

Then 2 weeks ago it just died one morning on the way to work, ive got it sitting here now.. and it had hot spots all over it and was down to the rivets and it falls to bits if i pick it up.

The clutch that came out was an excede but a shit one at that, so my cars had 2 clutchs as far as im aware within its 145,000km journey.

Dayne

my clutch died exactly a week after i put the exhaust and intercooler in :)

i was doing 100km/hr on the freeway and then suddenly the car quiet happily reved to 7000rpm in 5th gear :)

i got a exedy heavy duty clutch as a replacement for like $600-700 or so installed. I've had it for about 5 months.. Its starting to slip now so i'll probably get something abit better when finances permit :)

mine is an exedy twin plate extra heavy duty racing clutch and yes it hard to drive in traffic. defintely wouldnt recommend it on a daily driven car. was a very steep learning curve when i first got it.

cost me about $1800 including installed but its a bloody beast of a clutch. have had it in for about 5 months now and seems indestructable. :)

heheh well i only recently got the car.. NO mods except catback.. n the stock clutch slips in 4th n 5th..

But i have bought a heavy duty excedy clutch to go in there..

Seems like everyone is replacin stock clutch with excedy clutch.. hehe guess i did the right move n bought it for the best price ever (320-from C & B)

Edit: 78000ks.. im sure the clutch started slippin in japan probably a thousand or so ks b4..

i had a std broad minded personch in my car.... at 128,000 it was slipping... wouldnt grab when i did a quick shift... got a clutch from c& b and its awesome... can go mad launches... smells a bit tho but now its run in its all good......

had my car since 110,000km and dunno wat was the situation with the clutch...

but maybe it lasted a while because he had it since 70,000km and no recipts of a clutch being done....so maybe it was done in japan as there is writing on the origional one an shit...

My car had done almost 120,000km (stock) when I noticed the clutch wasn't grabbing too well. It wouldn't slip in 4th or 5th but hard changes wouldn't grab.

I then bumped it up to 240rwkw. Subsequently, the day I picked it up not only was the clutch unable to hold even in 3rd, but it was also raining so I had a shithouse drive home in my newly modified toy.

Then to make things even worse, by the time I got back from the Gold Coast to Brisbane the clutch died completely (couldn't even move in first) 6km from home and I had to get it towed. It was a crap night, I'll tell ya that!

Spent $1300 on a heavy duty ceramic single plate. Was a bit rough at first but now it's worn in and I'm used to it it works perfectly. No probs. Grabs very hard as well. Chirping into 3rd is no problem at all. Been going solid for a few months now.

Next time I'll probably go heavy duty organic though considering I don't race the car. Ceramic = overkill for a pure daily driver.

got mine with around 88000 kms from japan,

i put a high-flow cat and dump pipe on at 105000 and then it started to slip.it slipps in evey gear except first,when i put my foot down hard.smells bad.

its got a really heavy pedal,which i would love to know why...im sure a heavy duty clutch can have a light pedal? anyone know?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...