Jump to content
SAU Community

Recommended Posts

I'm looking at a set of 18" wheels (haven't bought the Stagea yet) and need to know the standard wheel dimensions.

It's a Series 2 if it makes any difference.

Anyone able to tell me what the Diameter, Width, Offset, PCD and standard tyre size are?

Cheers!

Edit... It appears to come standard with 215/50 R17 tyres

Edited by thedriver
Link to comment
https://www.sau.com.au/forums/topic/92233-stagea-wheel-dimensions/
Share on other sites

The R33GTR 17 X 9 X 30 with 245/40/17's clears the standard guards with the ride height at at 340 mm front and 330 mm rear.

The standard wheels were 16 X 6.5 with 225/50/16's

The PCD is the usual Skyline 5 X 114.5

:D cheers :D

Edited by Sydneykid

And SK comes through with the goods yet again. BIG THANKS!!!

I'm probably looking at 235/40 R18 which should fit I hope...

although, I just found out today I can get a set of 17" used Volks for $300 with rubber in near new condition.

18s are sooooo tempting though.

post-18577-1130468336.jpg

I'm looking at a set of 18" wheels (haven't bought the Stagea yet) and need to know the standard wheel dimensions.

It's a Series 2 if it makes any difference.

Anyone able to tell me what the Diameter, Width, Offset, PCD and standard tyre size are?

Cheers!

Edit...  It appears to come standard with 215/50 R17 tyres

Series II Stagea will take an 18" X 8" wheel running 38P offset - refer to attachment showing them on my car. rims are fitted up with 235/40R18 tyres.

marc2

  • 2 months later...
can anyone with an s2 rs four s check their placard on the drivers side door jamb to see the specs including offset and width of the original rims.

...Cheers

Tyre Placard photographed as requested from a SII - complied and Registered in QLD prior to registering in ACT.

Regards,

Marc2

ps. I cannot recall if rim offset was even mentioned on the compliance documentation.

post-18577-1136290826.jpg

That reminds me of a related topic...

... I was doing some research on tyre pressures when I found a WRX guy running 40 PSI even though the door placard read 32psi. Apparently Subaru changed there specs a few years back to keep up with current tyre technology but never changed the stickers.

What pressure should I be running?

My tyres are stock as per the door sticker - 205/55 R16 89V

can anyone with an s2 rs four s check their placard on the drivers side door jamb to see the specs including offset and width of the original rims.

...Cheers

i actually need the details from the placard of as "S" ie with 17" rims standard

That reminds me of a related topic...

... I was doing some research on tyre pressures when I found a WRX guy running 40 PSI even though the door placard read 32psi.  Apparently Subaru changed there specs a few years back to keep up with current tyre technology but never changed the stickers.

What pressure should I be running?

My tyres are stock as per the door sticker  - 205/55 R16 89V

I never take any notice of what is says on the door placard. Who knows how many different makes of tyres have been on the car since it was produced.

Check the sidewall of the tyre, it should have a maximum pressure printed on it. I normally take it to about 5psi less than that.

The tryes I have on mine came with the car. They are crap. On smooth surfaces they 'chirp' even if I take off gently. I think they are low rolling resistance tyres and therefore do not offer a lot of grip.

I will be upgrading soon to 18's as well, that should help the handling a little.

i still need to know what it says on the standard placard for an s2 stagea rs four s with 17" rims, as when i get my stagea complied i will need to source a set of rims that are like the standard ones.

i still need to know what it says on the standard placard for an s2 stagea rs four s with 17" rims, as when i get my stagea complied i will need to source a set of rims that are like the standard ones.

The only Stagea S1 with 17" rims standard I have seen is the 260RS. They utilise the standard R33GTR rims (what I have on mine). They are 17 X 9 X 30 offset with 245/45/17 tyres.

I had mine complied with the 16" rims and then put the 17" on later.

:nyaanyaa: cheers :blink:

Edited by Sydneykid
Oh, 260rs comes with custom BBS wheels made for hte 260rs, not 33GTR wheels.

However, they do look horn with those gtr wheels.

Well there you go, you learn something new every day, the 3 that I have seen all had R3GTR wheels on them.

:P cheers :O

Well there you go, you learn something new every day, the 3 that I have seen all had R3GTR wheels on them.

:P cheers :O

the original 260rs wheels are 17 x7 bbs .. front are +30 offset,rear +20 offset,you need spacers and longer wheels studs for rear to use 34or 33 gtr rims from my experience ..finding the right rims for my car has been a real pain ..so left them std ...too hard

post-7472-1136419095.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...