Jump to content
SAU Community

Recommended Posts

  • Replies 277
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Erin, please edit this if incorrect.

I'm not shouting - just making the message clear, as it hasn't been properly addressed.

ATT EVERYONE WHO HAS TOLD THEIR MATES TO COME.

DO NOT GET THEM TO COME IF THEY DO NOT HAVE A SKYLINE OR SKYLINE RELATED VEHICLE

EG Skyline/Cefiro/Stagea/Laurel

Please bring them in your car, the more the merrier.

THIS IS MSC (Massive Skyline Cruise)

This is probably the only club/forum event SAU QLD has where this is requested.

See you all there!

ATT EVERYONE WHO HAS TOLD THEIR MATES TO COME.

DO NOT GET THEM TO COME IF THEY DO NOT HAVE A SKYLINE OR SKYLINE RELATED VEHICLE

EG Skyline/Cefiro/Stagea/Laurel

What part of Massive Skyline Cruise don't people understand? the commodore cruises specify commodores only, why is it so difficult for people to comprehend that we only want Skylines/Cefiros/Stageas/Laurels to attend this cruise?

I think what would be nicer is to say.

PLEASE try your HARDEST to get your mates to go in your car. If they cant, they must make a minium donation of $50 or more, and stay at the back of the pack :P See thats nicer. Oh, and on the off chance there is any police trouble, they take it for the team!

I don't see what the big fuss is. it is being held by SAU....isn't that good enough. If you are so strict on SKYLINE, why invite stageas, cefiros and laurels.

I would say, bring all the people you can. Sure it is better to have all skylines but the simple fact is....it's not a perfect world, and that's the exact reason for us raising money in the first place.

If my Skyline broke down tomorrow and I couldn't drive it, I would be out there in the Mirage....and no-one can stop me.

HELLO ALL

I have a really ordinary stock looking red r31 aussie station wagon complete with rust . But its got a really interesting engine . You can pretend i,m not really with you and make me park down the back .

post-9523-1132875002.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Saw this video today from Adam LZ.    Long story short is he is claiming that the load from the engine fan once the fan clutch heats up(engaged) is increasing the getrag rattle(at idle) when you don't have a dual mass flywheel.  Before I go buying an electric fan setup .... Anyone heard of this ?    I must admit when my car is cold the getrag is pretty quiet and I do notice the rattle after it is all warmed up. I've always assumed this is due to the gearbox oil temp and tolerances of metal.       
    • Yep it sure does.   Tone wheel lines up in the same spot perfectly.    
    • Something I meant to say when we were chatting the other night about having an open trailer floor being great to work on a car, but you've never used the feature... It's a great place to park a car after doing suspension component changes, and do the tightening of all the bushes with the car sitting at full ride height. Especially when you don't have a 4 post hoist!
    • That is way more science than even I would use. I just eyeball it, not even accounting for the non-verticality of the tape measure when held on the lip and the centre at the same time. +/- 2mm is good enough for the girls I go out with.
    • So, before putting them in I need to understand the stock ride height. This is how I measured it: First, check the diameter of the wheel's centre cap, it was 52mm. Then put a piece of masking tape approximately across the centre and measure 27mm (half) from at least 3 sides to get a reasonable idea of the centre of the wheel cap. Mark that with a horizontal line as one measuring point. Then, directly above the wheel on the guard, put another piece of masking tape in approximately the centre. Use a string line to find out the point on the guard above the centre of the wheel cap and mark that. Then it is simple, just a tape measure to check the distance from centre of the wheel to the centre of the guard. Final results where  LF: 381mm RF: 379mm LR: 401mm RR: 400mm Pretty even considering they are 120,000klm old factory springs, lets call that 380 front and 400 rear.
×
×
  • Create New...