Jump to content
SAU Community

Recommended Posts

Hi ppl,

Just hunting round for a decent electronic boost controller and at the same time not spend too much.

I was looking at the Greddy Profec B-Spec II and the Turbosmart E-Boost 2 ones. Bit pricey but hoping to maybe find S/H.

Just want to know from peoples experience which has been good for them etc.

Cheers!

Link to comment
https://www.sau.com.au/forums/topic/95060-which-electronic-boost-controller/
Share on other sites

hey Pulp,

I've got an Greddy Profec -A, althou its not the one your looking at, i find it to be top, holds boost perfect and very easy to tune.

so going by that i would say the Profec B would be very similar.

Just had a quick look for Profec B and looks like the range from $300 to $500, if you cant get one for cheaper than $400 you might aswell go something like blitz ID-3

I know it's a bit off, but personally, i'm a Apexi fan. So it's the AVC-R. There's a reason why Apexi has not upgraded the AVC-R since it's launch, cause it just works so well. There is not much of a need to upgrade it. Some pple said that the AVC-R's solenoid is a perfect replacement for a skyline, which i think is just biasedness again, and should be bullshit. LoL.

My .5 cents worth. Again, remember. I'm a apexi fan. LOL

Thanks guys!

EVL, I'll check out the Profec -A, sounds ok.

KeeFy, yeah I like the Apexi gear too, am def getting an SAFCII and wanted an e-boost controller as well, but I think the AVC-R is pretty pricey compared.

I'll see what I find!

Doesn't really matter I spose Dan, is it better to buy through Nengun?

Although been speaking to Lumpy at Hyperdrive and he said cause my trans is Auto, to get the HP I want I'd have to go either PFC or a Greddy E-Manage kit. The SAFC combination wouldn't control or handle timing well etc.

The PFC would cost me more cause it takes more to tune with auto. So the E-manage kit would be a slightly cheaper and better option as it can be piggy backed.

pfc Does not work with auto nissans.

already been down this path.  I ended up getting  the emanage ultimate and profec e 01.

Yeah I'm thinking the same thing hey!

Did you do anything to the trans anyway? like any mods etc, or did it handle it fine?

no mods to gearbox as yet. will be getting shift kit form mv automatics though. PFC just will not work with the shift logic of the skyline gbox. I would have prefered pfc, but atleast you can hook emanage up to laptop and tune it yourself.

yeah i thinking of getting an electronic boost contoler looking for second hand APEXI AVCR i think they seem to be able to do the most rather than just plain two boost setting and thats it. Mines also auto buy yeah its a r32 so different to you guys.

Mad34 let me know when you get the shift kit from MV i was gona get one too and a trans cooler maybe cheaper to get together even if they are different

Hmm I've known a few people with AVCRs and even though they look nice, they've all had dramas. Not holding boost, too tricky to use etc etc. One of them switched to a Greddy Profec B Spec II and said it was awesome. Controlled boost a lot better.

But I do admit the AVCRs look sweet :)

E boost 2 are the best no spiking + you get a boost gauge with it

they are australian and the after sales is exerlent

i have one and was unhappy with it so i e mailed turbosmart and 30seconds no shit i had a phone call asking wat was wrong

they promtly told me how to use it my self now i agust it and my car is running very good

i have set it so good i hav the best power band and wen i get an e management i will play around with it again

james

theres a new blitz i-color or something with the slick colour screen and more logging/display options . the id3 has a mono screen and still has some pretty good monitoring/logging options

the duty cycle/boost curve learning thing can be tough to setup but its great when its working . the blitz can be set to manual if you want to go old school

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...