Jump to content
SAU Community

Don't Take Your Mum's New Camry To The Track.


Recommended Posts

hmm so his mistake was that he downshifted at high speeds around a bend?? Or the fact he went to fast into the corner? hmm ..

it's a combination, he got to the corner too fast and was then lifted off the throttle mid corner to down shift which generated a fair whack of lift off oversteer, he tries to correct a little but at that point seems to be hard on the brakes which in the massive slide he is now in means he has no traction to alter the cars angle and bascially just slides into the pond. :P

  • Replies 51
  • Created
  • Last Reply

Top Posters In This Topic

lol handbrake is gold, i just realised that if this vid matches that outside shot (it must!) then this qualifies for WELCOME TO LAST YEAR

Yeah it's defintely an old video :P

99% of SAUers would do exactly the same thing, or worse, as they have 100 more hp at their disposal and probably less talent. :)

Bit rich to sit back and bash the guy with your keyboards.

After he lost it he did the right thing...on the brakes!

I reckon good on him for having a go and not just modding his car with bullshit bling and acting like you are the long lost love child of fitty cent and paul walker...

who care its a gold video

wish i had one of when i nailled the wall at the track

all that money wasted and nothing to show for it

just ask duncan he has it on video

if i did i would have a small tv dedicated to playing it over and over again!!!!!!!!!!!

haha ill see if I can dig up the video...got in my hdd somewhere...

its a guy named russell going around wakefield in his red wrx..and some hillarious commentary to boot...

I'm holding out to see it!

Impressive.

I would have thought a badly-done downshift would have compression locked the front, causing that to wash out instead.

But at the same time unbalancing the car mid corner, big no no... heal and toe!!! :P

Here's the thread - unfortunately it doesn't look like the vid is still up  :(

What about the brakes Russ?

Starts around post #34.

Did anyone save a copy?

yeah I saved a copy......but I dont know how to upload videos on to this forum.... :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...