Jump to content
SAU Community

Recommended Posts

  • Replies 183
  • Created
  • Last Reply

Top Posters In This Topic

A little under $6k got me:

STRIP & CLEAN 6 CYL TWIN CAM ENGINE

BORE & HONE 6 CYL ENGINE WITH TORQUE PLATE

MILL 6 CYL BLOCK

CHECK SIZE & POLISH 6 CYL CRANK

SUPPLY AND FIT SCREW IN OIL GALLERY PLUGS TO NISSAN L/RB/CA/SR CRANKSHAFT

CLOSE AND GRIND CONROD

PIN FIT ROD

SHOT PEEN CONROD SET

BALANCE 6 CYL ENGINE

FULL HEAD SERVICE

FULL GASKET SET- NISSAN RB25DET

COMETIC MLS HEAD GASKET

WISECO FORGED PISTON W/- RINGS

ARP ROD BOLT SET- RB30

CONROD BEARING SET- NISSAN RB30

MAIN BEARING SET- RB30

GATES RACING TIMING BELT

TIMING BELT TENSIONER

BLUEPRINT ASSEMBLE 6 CYL DOHC LONG ENGINE

SUPPLY MACHINE & FIT OIL PUMP DRIVE COLLAR- RB25/RB26

I supplied the cams and paid to transport the engine to and fro which wasn't much considering.

knore,

not that you are asking me but... When I had my motor built up it was sat on a pallet, strapped down and glad wrapped up.

Fork came along and dropped it on my trailer that had a nice thick rug on it so I was able to slide the pallet off.

Myself and my other half then slide the pallet off the trailer on to the ground using a few bits of wood.

Easy Peazy.

One of the SAU NSW club members helped me out with TNT to transport it.

Best to get your engine builder to book it on their account and then bill you, that way you get proper trade price.

I drove to an industrial area (not far for me) and looked around for a pallet of the right size (you want one about half or even less the normal size). It was easy, had plenty to choose from. Companies just stack them up near their rubbish bins.

I bought a twin pack of those snatch straps for about $10 and strapped the engine down tight.

One of the SAU NSW club members helped me out with TNT to transport it.

Best to get your engine builder to book it on their account and then bill you, that way you get proper trade price.

I drove to an industrial area (not far for me) and looked around for a pallet of the right size (you want one about half or even less the normal size).  It was easy, had plenty to choose from.  Companies just stack them up near their rubbish bins.

I bought a twin pack of those snatch straps for about $10 and strapped the engine down tight.

Ok thanks, so you pulled engine out yourself, put it on a pallet, strapped it down and then got TNT to pick it up and deliver to proengines.

Then when it was done proengines got tnt to pick up and deliver back to you?

  • 10 months later...
It is about my rebuild but it was also supposed to be a repository for NEO info which it has turned out to be.

Shonen - you're obsessed with highmount. I'm more likely to put nos on it than a highmount. That said, a 2835ProS would be nice but I can't afford anything atm.

I've already got the highflow so I'm sticking with that due to $$. I've got some cams going in though so that should make some difference.

I think the 4 doors have the viscous LSD and the 2 doors get the helical LSD which means I'll be up for a new diff at some stage.

I was pretty sure all the turbo (2dr and 4dr) have the helical diff and only the autos have the viscous LSD's? Does anyone know this for sure?

Pete,

* The internal diameter of the stock GTT guage holes is 60mm

* Defi BF guages (amber or white dial) are only available in 60mm

Therefore the Defi BF (60mm) gauges will fit fine as you can see from the pics, but the bezel will be mounted outside the hole.

This pic shows Defi black 60mm gauges (not BF) fitted.

post-6399-1136350235.jpg

Not enough gauges here.... :ninja:

JustinP; you want ideas on how to install a e-01 in the R34? We've done two now (one on my one and one for a customer) and we concluded that there is only one spot for it... and that's in front of the centre vents.

Custom bracket needed to be made...

JustinP; you want ideas on how to install a e-01 in the R34? We've done two now (one on my one and one for a customer) and we concluded that there is only one spot for it... and that's in front of the centre vents.

Custom bracket needed to be made...

Yep any ideas would be great :)

I was thinking of removing the ashtray, bolting in a bracket inside, and mounting it as low as possible there. I figure it will cover some of the double DIN stereo but don't mind. Think this would be possible? My gf said she would rather if I didn't cover the vents heheh

I don't actually have the E-01 yet so I haven't got a real idea on the size of unit yet, I guess I should check the specs on it.

Well the way I've done it is actually just using an upside down L bracket which "hooks" onto the air vents...

1) It's removable for security

2) It looks neat

3) You don't have to look all over the place whilst driving

4) The rather intrusive wiring can be run into the vents

5) Ventilation keeps the unit "cool"

6) Keeps double din area completely clear

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...