Jump to content
SAU Community

Recommended Posts

Hi everyone

I just installed an oil temp guage and was wondering what the normal oil temp should be while just driving around, ie crusing. With an oil cooler I should add. Today on the way to work was my first test and the guage barely moved from 40 deg (the lowest value). At first i thought i had wired it up incorrectly. Though after filling up the car I got back in and the guage read 60 deg. Then as soon as I start driving it went back down to 40 deg.

Does this sound like a normal temperature? Sounds low.

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/
Share on other sites

Weird

that is way too low.

The temp on a gtr sits around the 80 degree mark, which is very similar to water temp. then with a cooler once you get up and moving, it can vary between high 60's and high 70's depending on how hot it is, how fast you are driving, etc.

But ideally it should sit around the water temp mark unless you are giving it

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1735572
Share on other sites

Oil takes a long time to get up to coolant temp .If you only drive short distances it will never get up to normal temp .

If you drive it hard it will get a lot warmer than coolant temp and it depends on how hot the ambient temp is .

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1738567
Share on other sites

it sounds like your oil cooler is doing too good a job on the street. There are two options, one is to fit an 'oil-stat' or you can simply block off all or part of the core (just use a pice of sheet aluminium) for street duty, then remove it when you do drifting. ideally your oil should be above 70 degrees, but 80-90 is good. 40 or 50 is too low.

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1739382
Share on other sites

That was during the cooler periods

With the oil cooler, not once have i seen the oil temp hit over 90 degrees.

Prior to this, it would rise to about 95-100 or so degrees after a long highway journey (1hr+), continous revving @ 3k in 5th. Now, it goes down to around the low 70 degree mark

Oil pressure gauge at idle is close to 2, bit of throttle gets it up to around the 3 mark and the highest i think ive ever seen it is around the 4 mark

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1739386
Share on other sites

I actually think my oil temp guage is not working. Its a crappy Auto Gauge brand. The needle wobbles about all over the place. I guess thats what you get for buying a $30 guage. Gonna test it with a jug of hot water. If it doesn't give me a real reading its going in the bin.

Link to comment
https://www.sau.com.au/forums/topic/95893-normal-oil-temp/#findComment-1743982
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...