Jump to content
SAU Community

Recommended Posts

2pm it is then

soo:

2pm at the servo/macers on Briens Rd, and the corner of Redbank Rd in Northmead

good? :)

Is this meet still on?

Anyway...I'll drop by the maccas at 2 and see if anyone is there...if not I'll just go there anyway. Can't wait to see 2GUUP for real, rather than looking at a pueny avatar.

BTW. I'll be the guy in the grey R33 standing around like an idiot coz he doesn't know anyone else from SAU.

Cheers

Sam

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

Twoogle made ~430awkw this arvo. A VR ute made about 500rwkw, an RB26 R33 GTS-t made about ~420rwkw, a Supra made 600rwkw.

The Autosalon definitely is getting better (as in more tasteful mods rather than just pure bling on excels). I only noticed 2x R32 GTR's (including Pauls) and probably about 5-7 Skylines in total.

Sooo many damn promo women it's pure heaven :)

Twoogle made ~430awkw this arvo. A VR ute made about 500rwkw, an RB26 R33 GTS-t made about ~420rwkw, a Supra made 600rwkw.

The Autosalon definitely is getting better (as in more tasteful mods rather than just pure bling on excels). I only noticed 2x R32 GTR's (including Pauls) and probably about 5-7 Skylines in total.

Sooo many damn promo women it's pure heaven :P

new rubber tommorrow (a "bit" of wheelspin on the Federals) will hopefully have a slightly higher figure in all wheel mode...we are going to try to beat our rear wheel record too....mickey thompson drag tyres on a dyno??? well they did call it "Dyno Drags"

(where was the second dyno they were spruking about??)

Edited by DiRTgarage

well done paul....

the m/t drag radials will be cool for one or 2 pulls...

make sure you run 40 to 50 psi in them...good luck for sunday

mark.

new rubber tommorrow (a "bit" of wheelspin on the Federals) will hopefully have a slightly higher figure in all wheel mode...we are going to try to beat our rear wheel record too....mickey thompson drag tyres on a dyno???  well they did call it "Dyno Drags"

(where was the second dyno they were spruking about??)

what colour was the supra....

was it the purple supra form millenium motorsport...

cheers, mark

Twoogle made ~430awkw this arvo. A VR ute made about 500rwkw, an RB26 R33 GTS-t made about ~420rwkw, a Supra made 600rwkw.

The Autosalon definitely is getting better (as in more tasteful mods rather than just pure bling on excels). I only noticed 2x R32 GTR's (including Pauls) and probably about 5-7 Skylines in total.

Sooo many damn promo women it's pure heaven :P

It was from M'Motorsport unsure if it was blue/purple though because of the sunlight shining on it.

From memory it made 600.3rwkw and 599.x rwkw in the 2 runs it did (and apparently it had a 50hp NOS kit ready for todays dyno runs).

well done paul....

the m/t drag radials will be cool for one or 2 pulls...

make sure you run 40 to 50 psi in them...good luck for sunday

mark.

yes....correct, forgot that the tyres only had 14psi in them. Cold tore rubber off them in big chunks......big mistake.....ahh well never mind.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...