Jump to content
SAU Community

Recommended Posts

Sky30,  I have not personally compared the two gearboxes side by side fully dismantled, but know someone that has.  There is one bearing with a different Nissan part number, not sure which, but both bearings are physically interchangeable and probably make no real practical difference. It is the sort of production change that car makers sometimes make during a production run.

The 4WD gearboxes are essentially otherwise identical in all respects, and used in both GTR and GTS-4. Gears, casing, shafts, selectors, seals, transfer case, everything are absolutely identical.

Diffs are the same too. R160 in the front and R200 in the rear all are 4.11 ratio except the R32 which has 4.32 diffs.  The rear LSD can be viscous, multi-plate, or electronic, depending on what was ordered.  Some GTS-4s even have the electronic diff usually only seen in the V spec GTR, though that is extremely rare.

The R34 GTR with the six speed Getrag has different gear ratios and diff ratios again, (3.54, I think ?). The front diff is an R180.

I was also tols the GTS4 transfer case has less clutch packs than a GTR?

GTS-4 and GTR gearboxes are identical, except that the R32 GTS-4's (with the RB20DET) used different ratios. The R33 boxes and diffs are identical ratios.

But driveline strength also must include the clutch and half shafts. The GTS-4 is considerably less than the GTR in both clutch capacity and rear half shaft diameter. It also uses four stud wheels.

If you get an R33 GTS-4 and put a GTR clutch in it, and upgrade the wheel hubs and half shafts, it will be identical to a GTR in both strength and ratios.

But an R32 GTS-4 will have different ratios, but could be made just as strong with the same clutch and driveshaft changes.

Ginkgo Biloba i was replying to this post.

Targa spec GTRs put out around 250rwkw, so not big power. But 30 6000rpm launches in 6 days as well as a season of 8000rpm race launches are a pretty good test.

Standard diffs, standard gearbox. We regularly have to replace gearboxes with synchro problems but we've never broken anything inside. Never had any trouble with the diffs they are a pretty strong piece of gear.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...