Jump to content
SAU Community

Recommended Posts

hi i am after a rb20det halfcut to convert my silvia from a ca18det to a rb20det... i am seriously in the market for one and have the cash waiting.. no mucking around

if no one has one wheres the best place to get one.. i live in brisbane but i herd many people get them shiped....

i am going the rb20 as they are getting alot cheaper now

if someone can seriously help me find a good one for a good price i will give u a 50 dollar spotters fee :) or a carton of piss :)

0433 754 644 or 3343 7941 or [email protected]

thanks very much in advance

hal :D

Link to comment
https://www.sau.com.au/forums/topic/97960-where-to-get-a-good-rb20det-halfcut/
Share on other sites

Ichiban, ekw, rolin imports, just jap, sss automotive, stz automotive, there are a few other good places... I am also looking for a RB20det, to put in to an r31, so if anyone has any recomendations, please go on....

Watch out about this, don't be tempted by the lower price of RB20 over SR20. That

might sound good on it's own, but the cost is considerably higher to put the RB20

into the engine bay of a CA18/SR20, I don't think anyone's mentioned this point

yet... :huh:

What you save in engines you might lose in installation. A bit of custom work is

involved in doing an RB -> SR/CA conversion, whereas an SR20 swap over a CA18

is relatively much easier and cheaper to do.

So, bear that in mind, but if you're still keen, I love your enthusiasm! B)

Adrian.

i know someone/somewhere where i can get it done now.. so i am seriously looking for a rb20det halfcut.. if i cant find one sr20det we go then :)

if someone knows a place or someone around brissy that has one... or someone that has a project they forgot about and have a remains of a halfcut lieing around get in touch with me please

cheers

hal

Well, I know of a few, but they're all in Adelaide. If you're that keen on having an

RB20, then do it. No use saving a few bucks if you're not happy with the result.

If you're willing to get one from Adelaide, try the following places:

Z Imports

Jap Parts

Adelaide Jap

D1 Garage

Autotech Imports

Good Luck! :)

so you've tried rolin and Asian autospares up here? and no go? they usually have a couple.

I've got my engine in my car.. but i am going on holidays till mid-jan. End of jan could talk if you haven't found one. Would be engine loom+ecu+engine for around $1000.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...