Jump to content
SAU Community

Recommended Posts

Hi guys,

I have a R33 1996 GTST 4door sedan auto.

I have done a search and it seems that the standard boost for a R33 GTST is 7psi, but couldn't find any thread that matches and answers my querie.

Basically, my friend who drives a R34 GTT noticed that my standard boost guage is not reading above the half way marking being close to 7+mmhg? Which I believe is where it should read at max boost (i.e7psi).

I have a turbo back exhaust and big pod, would expect to be getting close to 8psi.

We disconnected the boost controller and still no difference? Is there something wrong with the boost control or is it the guage?

Any advice is much appreciated.

Link to comment
https://www.sau.com.au/forums/topic/98109-calling-boost-experts/
Share on other sites

what controller are you running, and also and yes 7psi after 4500rpm if you have stock controller or 4-5psi before 4500rpm and the gauge is reading right 7+mmhg=1.0bar which is 14.5psi so half gauge is right, the stock gauge may be not so acurate as compared to a hks but and also do you have any mods.

what controller are you running, and also and yes 7psi after 4500rpm if you have stock controller or 4-5psi before 4500rpm and the gauge is reading right 7+mmhg=1.0bar which is 14.5psi so half gauge is right, the stock gauge may be not so acurate as compared to a hks but and also do you have any mods.

It's stock a controller, and at max boost it's just below half way? Though it would be above, as friend's stock R34 GTT (with pod and cat back), at full boost is above half way mark. So R34 GTT's run higher stock boost??

Thanks.

Edited by godspd

Works like this.. from 0 - 4,500rpm - they run 4-5psi (depending on other factors) once it hits 4,500rpm the solenoid opens bleeding more air which will cause it to go to 7/8psi from there to redline.

mine - which is mainly stock did this but went to about 0.66Bar which is about 9psi so it can vary a little..

if it isn't going past the 1/2 way mark - check your going over 4,500rpm :(..

if your mates hits 8psi before that mark, he's probably got the boost solenoid out of the loop.

check under your bonnet and see if it's still hooked in and plugged in, it's on the right side under the stock air intake..

you could always get a turbotech boost controller and try using that instead..

Works like this.. from 0 - 4,500rpm - they run 4-5psi (depending on other factors) once it hits 4,500rpm the solenoid opens bleeding more air which will cause it to go to 7/8psi from there to redline.

mine - which is mainly stock did this but went to about 0.66Bar which is about 9psi so it can vary a little..

if it isn't going past the 1/2 way mark - check your going over 4,500rpm :D..

if your mates hits 8psi before that mark, he's probably got the boost solenoid out of the loop.

check under your bonnet and see if it's still hooked in and plugged in, it's on the right side under the stock air intake..

you could always get a turbotech boost controller and try using that instead..

Yes your absolutely right, it hits 7/8psi above 4500rpm due the opening of the solenoid (friend with the R34 knows this too) that's why he picked up that something might be wrong with my boost. The problem is that mine dosn't even do this at 7000rpm??? it just stays below the half way marking of the boost guage at full boost, which is telling me its around 5/6psi?? Something wrong here?

from the sounds of it you should possibly check the solenoid.. check the plumbing..

if the solenoid isn't opening about 4,500rpm you'll never get higher than 4-5psi..

It actually feels like, boost changes from around 3000rpm?? but not 4500rpm?

sooo..

It actually feels like, boost changes from around 3000rpm?? but not 4500rpm?

With a auto, you actually don't feel that big change in boost heheh, its quite progressive unfortunately...

huh?? I don't understand.. i'd be hell surprised if you can't notice a change by approx 30% in boost pressure.. you'll notice it whether it's auto or manual..

and the change at 3,000rpm.. that's not the solenoid.. the solenoid works from 4,500rpm.. not 2,000.. not 3,000..

We disconnected the boost controller and still no difference? Is there something wrong with the boost control or is it the guage?

what boost controller??

if you disconnected it without putting the solenoid back in the right way you will never get over 5psi..

did you plug it all back in with the T piece or did you just "take out the boost controller" ..

sorry.. just had to vent a little

edit: oh and one more thing, go and get a decent boost gauge..

Edited by Links
Hi guys,

I have a R33 1996 GTST 4door sedan auto.

I have done a search and it seems that the standard boost for a R33 GTST is 7psi, but couldn't find any thread that matches and answers my querie.

Basically, my friend who drives a R34 GTT noticed that my standard boost guage is not reading above the half way marking being close to 7+mmhg? Which I believe is where it should read at max boost (i.e7psi).

I have a turbo back exhaust and big pod, would expect to be getting close to 8psi.

We disconnected the boost controller and still no difference? Is there something wrong with the boost control or is it the guage?

Any advice is much appreciated.

the half way point on a standard gauge IS just over 7psi.

and if u're not running more than standard boost, it'll hit half way on the gauge mid way thru the rev range.

so it's running fine.

sooo..

It actually feels like, boost changes from around 3000rpm?? but not 4500rpm?

With a auto, you actually don't feel that big change in boost  heheh, its quite progressive unfortunately...

huh?? I don't understand.. i'd be hell surprised if you can't notice a change by approx 30% in boost pressure.. you'll notice it whether it's auto or manual..

and the change at 3,000rpm.. that's not the solenoid.. the solenoid works from 4,500rpm.. not 2,000.. not 3,000..

We disconnected the boost controller and still no difference? Is there something wrong with the boost control or is it the guage?

what boost controller??

if you disconnected it without putting the solenoid back in the right way you will never get over 5psi..

did you plug it all back in with the T piece or did you just "take out the boost controller" ..

sorry.. just had to vent a little

edit: oh and one more thing, go and get a decent boost gauge..

Its cool mate, we didn't take out the solenoid, just "unplugged the boost controller.

Plus what I am trying to say is that there is no jump in boost from 4500rpm, only which seems like to happen at around 3000rpm, but I could be wrong, as one can't look at the factory gauge on the dash while at the same time driving :)

hi mate,

just to let yo know that the stantard boost for the rb20det and the rb25det is

8 PSI as quoted in high performance imports magazine.....

hope it helps :)

Half right and half wrong.

The satndard boost for an RB25DET is 7/8 PSI

The standard boost for an RB20DET is 10 PSI

Just wanted to clarify this so no one3s gets confused.

The stock boost guage IS accurate. Your boost levels are fine, and for the record...the 34 guage reads in different measurement anyway.

Don't compare your guage to your friends 34 guage. Just take a reading...go to google and type in 'convert mm/hg to PSI'. Then work out your boost level from there. You will see that the stock guage is ok.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • PRICE  : $1400 LOCATION   : NSW Central Coast FIT  :  All Nissan 350Z type Z33 and Infinity G35 Coupe. See delivery note. Hi, brand new, unused, still in the box.  ($1850.00 is what i paid ) My bad luck !!! I thought my right front  Bilstein was cactus so i bought the ST 's to replace all.  Turns out the right front is fine ( loose mounting after service  by a well known importer of Bilsteins ) So im selling the ST's. They are made by KW ( no intro needed ) . Iam on the Central Coast and im willing to meet up in Sydney metro, within reason and Newcastle.
    • Yep, yeah would need to do the flywheel although the 6 bolt NA clutch can handle a 20de if just wants to replace the stocker.
    • No it's fine. Heat sleeve is a thing. With oil running through it it is unlikely. Engine off heat soak can be a thing though. There is no way that you have a leak through the hose. That has pressure behind it and any small hole will turn into a large one in very short order. It is so much more likely to be leaking from the connection.
    • Really? That's piss weak. I didn't know they hobbled the shitboxen that badly. OK. So probs need to buy a flywheel too. But that's not too bad.
    • Hi all. I already posted some newbie-ish questions here and there but this will be my first "big" post. Last summer I went and fulfilled a kind of childhood wish, because I just thought I needed this experience in my life no matter what. The car I bought is a mildly modded 1995 BCNR33 Vspec. It was repainted to a metallic orange color all around and it had all windows reseated. Not so well done black respray in the trunk and a metallic black in the engine bay. From outside it looks very nice except for a minor paint error on the roof and the rear spats needing new adhesive tape. The inside is pretty clean and no broken plastics, missing or faded buttons. Even the adjustable mirrors and trunk antenna work like a charm. Despite a moderately long list of issues I don't (yet) regret buying this car. Most mechanical problems are just due to age, like worn rubbers here and there. The underside sadly has lots of corrosion, especially to the back. It looks like it either has been driven in the winter for a while or it lived near the saltwater in Japan, the rust is nothing terrible but it'll require to be looked after. Mostly panel gaps and all the mounted components underneath are a bit crusty, but I don't think anywhere has progressed so badly that there's going to be holes. Front right jacking rail is crushed and needs some care so it doesn't develop into a rust crater at some point. Worst part is definitely the strut towers. I thought they looked fine but after taking off the strut bar I noticed that it actually started bulging up on the passenger side. Probably would have passed on the car or negotiated down by some thousand Euros more if I had noticed this before buying, but here we are. Trunk area also has signs that there was a water leak to the interior once but nothing too crazy, I guess lots of Skylines had this at some point. As for the list of (known) issues, I'll try to make this compact. I hope the coloring is self explanatory. Mechanical: -Various busted or soon-to-be busted rubber bushings and ball joints. Will replace ball joints with OEM or better and bushings with polyurethane where possible. -Shaking steering wheel at above 80kph -downshift from 5th to 4th is a bit crunchy unless I rev-match, might just try to renew the shifter assembly, but it's not a priority issue -tailshaft centre bearing could use a replacement, is it worth going 1-piece tailshaft as it doesn't look too fresh all around? Chassis: -underbody corrosion on many spots and in hollow spaces, needs to be treated -corrosion on many bolts, hoses, lines, suspension components, subframes, will be treated when replacing of the bushings is needed as time goes on -strut tower top panels and some of the surrounding panels are rusty, so needs fixing. Will look into doing this with a buddy in the winter, otherwise bite the bullet and pay a professional -driver side door is misaligned to the body and needs to go a slight bit more inwards -both door windows are misaligned and have an airgap where the window meets the door at the B pillar -The Aerocatch latches for the bonnet have locks but no keys, need new keys. -driver side door window is kind of gritty and could use a polish -damaged jacking rails and front frame rails, from people lifting the car the wrong way, might have this fixed by a bodyshop Electrical: -Nismo tachometer is just bouncing and displaying nonsense, supposedly worked fine when the stock ECU was still in the car -An old Greddy boost controller sits on the dash which will be removed as it servers no purpose anymore. -a led segment rpm gauge is on the steering column, will probably also be (re-)moved once the Nismo tacho is working correctly -there was an attempt to make the sound system better by the previous owner but it was just inducing noise all the time, ripped out the amp and filters in the back, no music for now -trunk antenna goes up as long as the radio is on regardless of the mode, I want it to only rise if I choose Radio specifically or per switch -3rd brake light is a bit dimmer than the taillights but everything was converted to LEDs so mabye now it just seems dimmer? -reverse light flickers, have to test if that behavior changes when I fiddle with the gear stick. Hope I can get around changing the switch. -Left side taillight, blinker section has minor water intake and is humid after washing. Other side has a hole in it, probably for that exact reason. I'll probably reseal them entirely and plug the holes. Engine: -minor coolant drips on one or the other hose -rear turbo leaks oil onto the exhaust making the car essentially undriveable due to fire hazard -Oil filter relocation kit has an oil drip at the Dash lines, will probably make a new connection there and tighten real good and pray -throttle body assembly is slightly stuck for the first throttle pedal input after sitting for a while I'm always open to suggestions and advice from more experienced people, I'm sure half of this list is easily dealt with and just requires some time and effort to sort out properly. Once I have some proper pictures of the car I will post some in this thread, I just have to remember to take some more once I get the chance to. Will post updates when I have news on anything, I want to try to keep this thread as kind of a logbook as well. Ultimately my goal for this car is to just enjoy it. An engine rebuild is probably going to happen sometime as well, because it is old after all. It will never be fully new again, I am just not that rich. But I want it to look good, work well and not rot away while I drive it. I'm probably gonna spend a lot of money on this journey, hopefully not an unreasonable amount.
×
×
  • Create New...