Jump to content
SAU Community

Recommended Posts

Hey all,

I test drove a 92' R32 GTS4 the other day, it has 143,000km and mods include: lowered on king springs, hybrid front mount installed, organic h/d clutch, running 13-14psi via one of those t-shape boost controllers, full 3.5" turbo back apexi system, apexi pod filter. It has had its major service apparently.

The problems the car has at the moment are;

1) Syncro's for 3rd, 4th and sometimes 5th are farked, it crunches hard into 3rd and 4th if you don't change into them ever so slowly (then it doesn't crunch if you REALLY baby it into gear).

and 2) The rear diff makes a whiny noise at about 80km/h-90km/h, then when you get up to 100km/h it appears to go away. Isn't overly loud, but is noticable.

3) The rear door locks dont function properly, the right rear door you cant open from inside or outside, and the left rear door you can only open from inside.

4) Front left brakes make a bit of noise sometimes (they've just been machined, the guy reckons all it needs is a $5 brake pad clamp to fix)

Aside from that, the car drives very nicely and is quick. The interior is awesome and is the updated stuff, MUCH nicer than the 1989's, the paint work is also awesome.

Are these problems indicative of any kind of serious misstreatment of a GTS4? I mean, it's probably been given a bit in its time like all Skylines, but if the compression is good on the motor is it still worthy of a buy? The seller says his mate who runs a performance workshop can supply a new GTS4 box and install for ~$550, and can supply a new rear diff for $125. I'm dubious about how much it will cost to fix the 2 rear doorlocks though. I can pickup the car for ~10,000.

Constructive opinions please :)

Edited by esprit
Come on guys need some knowledgable opinions here!

The car is 15 years old, has done close on 100,000 miles. So it will probably be tired - it certainly sounds it. For my ten cents it is probably better finding something that you don't have to spend 2 or 3 thousand on to get it up to scratch. There should be loads of R32 on the market presently.

By my calculations:

1) New gearbox supplied and fitted - $550

2) New rear diff - $125 (self fitment)

3) Rear door locks - $100-$150

So its not going to cost me another $3k at all really.

It was compression tested today:

145, 145, 145, 145, 140, 139

The car is 15 years old, has done close on 100,000 miles.  So it will probably be tired - it certainly sounds it.  For my ten cents it is probably better finding something that you don't have to spend 2 or 3 thousand on to get it up to scratch.  There should be loads of R32 on the market presently.

A lot of the R32's on the market have sub 100,000km odo readings, which I really find hard to believe. It's obvious they have been wound back and have probably done 200,000+ (especially the 1989-1990 models).

There is a lot on the market, but most are 1989 models (which are horrible inside), and people are asking too much for them as well.

Symptom 1 is a sign of a bad manual driver :D

the rest are just signs of age. Most of which are easily fixable. Any mechanic/auto elec should be able to sort out the door.

10k is not a bad price for a GTS4 that came in under the old CPA scheme, and isn't on the verge of a coronary like some of the 15 yr old ones that people pick up cheap to make money on.

What's the rest of the car like, interior, panels etc? rust? bends, dints, dents, scratches?

ok i got my 89 4door gts-t, wit 61 thou on it, its not wound back because u can tell if u throw it on the hoist, it has little dirt on the under body, i know it may be rare but its still achevable so dont rule out a 89, btw it snot much diff to the new 32's on the interior, so im guessing its a 4 door?

So little dirt under it? they probably washed it for that particular reason. to make people believe the ks.

When I first got my car, it looked spotless under it like it was a brand new car. 5000ks later, it now looks as dirty underneath it as my dad's car with 100000ks on it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Intake manifold is not a part of the issue. The turbo bolts to the exhaust manifold. That is easy. But close your eyes and picture the physical situation. That is a T3 flange on the manifold and a T3 flange on the turbo. As long as any new turbo has a T3 flange on the exhaust housing, that exhaust housing will bolt to the exhaust manifold. This places the exhaust housing in the same place as the stock one. But now move your mental attention a little further forward. The location of the compressor housing is set by the length of the turbo's core. The stock turbo had a long core. Let's say that it is..... 100mm long. So that would place the compressor housing 100mm forward of the exhaust housing. But a highflow, might well have a centre core that is shorter. Let's say that it is only 70mm long. Now the compressor housing will be 30mm further back in the engine bay than the stock one. This DOES move the turbo's compressor outlet backwards. It also moves the compressor's inlet backwards. You will very likely have to do some work to both the inlet and outlet piping to make everything connect again. I am not say this to make it out to be a bigger deal than it is. I am just pointing out that "bolt on" is sometimes not quite bolt on. The highflow from GCG that Murray linked above (https://gcg.com.au/turbo-charger-upgrade-skyline-gtst-2iu-xtrgts-s1.html ) uses a core that is the same length as the stock core, and so does not require this extra work. It will look very much like the stock turbo. No-one uses GTR turbos of any flavour (stock, or aftermarket) in a single turbo application on RB20/25. It's not a thing. Yes, people have been putting on GT3076, GTX3076 (and bigger and smaller versions of those) and G30s (of various sizes) onto RB20/25 since forever. But these are not "bolt on". Everything except the 4 bolts to the exhaust manifold change with these. And genuine Garretts are expensive. Non-gen, like Pulsar, etc, are cheaper, variously as good or nearly as good. But still not bolt on. No-one in the right mind would pay for an HKS turbo. Not in this modern day and age. Well, yes, the GCG highflow. You could ask HG what he can do to make the compressor housing sit in the original location. There are surely others doing highflows around the world. And some of the eBay/Temu ones (as reported by Dose) work and don't die. Bit of a lottery though. I would send your turbo to GCG (here in Oz) to be highflowed if you want a trivial no-extra-work option. But seriously, the work required to change inlet and outlet piping is not that hard. That's a boost control problem, not a turbo problem.
    • Thank you all for the replys 🙂 I know that intake would be different but that is one pipe at it is not that hard to get(custom one). I meant mainly bolt to the stock manifold and the turbo elbow. I looked and many sites/forums but they are just "old" with some old HKS turbos from GT-R i guess? What about some Garrets?  Or any other turbo? Is there even a turbo which i can just bolt on? 😄 And yeah i know about that new HKS but that is like 2000k USD without taxes/shipping in here   Iam getting a touch up tune but my "problem" is that on the "not" hot day iam getting peaks around 0,9 bar...and when it was around 15 Celsious i saw peak around 1 bar which is just too much for stock turbo. And of course turbo is old and i like to get some new one for a piece of mind 🙂 
    • I'm working on the assumption that our friend Jasmine here is a Russian (or, possibly Ukrainian) spammer/spambot, based purely on the number of such that I have been having to neuter in the last few weeks. IP address for the OP above was in WA. But that could have been via VPN. Posting at quarter to 4 in the morning is a good sign of being from somewhere in Europe. The last Jasmine that I kicked in the cooch was IP addressed in Ukraine. Even that could have been via VPN, and the bitchbot could have been from Russia, Serbia, China or anywhere. Regardless, was a spambot, so I killed it with fire. The fact that our new friend Jasmine here did not respond in any way to my tart query strongly suggests to me that this OP was just the establishment phase of a user able to be activated for spamming in a week, or 3 or 10.
    • The stock manifold is "mostly" divided. The divider actually has a notch cut out of it where it would meet the divider on a twin scroll housing. I have no idea why. But whatever the reason, it would cause some cross talk when used with a twin scroll housing. People do put twin scroll housings onto that manifold. But I'm of the opinion that proper twin scroll internal gating is...not really possible at this scale. You'd be throwing good effort (ie $$) after bad, when you really should be doing something else. Notwithstanding that.... I am not sure what the idea that you are floating has to do with the difference in comp cover position caused by the highflow using a shorter length core than the stock Hitachi one. Can you clarify what you meant?
    • Majority of regulars are > 30. We all act at least 50. Definitely not friendly as we're all grumpy. 😛
×
×
  • Create New...