Jump to content
SAU Community

Air Con System Flushing

foznice

By foznice,
in Victoria

 Share

Recommended Posts

foznice Veteran

foznice

Posted
Posted

Evening peoples,

My car's being imported, and as many of you know part of the process is degassing the air conditioning system before it travels oversease (anyone know why?)

I've heard that some people have special equipment to flush out the airconditioning system of dirt and any other crap that may have accumulated in the piping in the time that the canister has been disconnected and the pipes are left in the open.

Before regassing the system I thought it would be a good idea to have it thouroughly cleaned out.. if your gonna do it you might as well do it well..

sooooooooooooooo.... does anyone know anyone particulary good who may be able to do this cheaply?

Do most car airconditioning specialists have the required equipment to clean out the system?

Cheers :D, and merry christmas

Link to comment
https://www.sau.com.au/forums/topic/99472-air-con-system-flushing/
Share on other sites
MFC05 Experienced

MFC05

Posted
Posted

a few of my mates who are private importers they do the dodgy by not brothering Degassing the air-con im not to sure what will happen if u dont apparently the gasses they use in japan are differnt from here i donno why it has to be degassed

all i know is my mates 300s and R32s all didnt get desgassed and still got imported !!

dezz Grand Master

dezz

Posted
Posted

hmmm i forgot all about getting mine re gassed, but when i checked my car out at UPI, i tured on the A/C after the car had been running a while, and the air it was blowing was pretty cold...

now im not an A/C expert, but does de-gassing mean it shouldnt be blowing cold air like it normally would until its been regassed?

dezz Grand Master

dezz

Posted
Posted

interesting. my invoice for the car in japan after the auction lists

"de-gas" on it as well as transportation to the dock etc, doesnt say air con...just de-gas...

i dont really care, as long as i dont get bird flu/SARS when i have my A/C on, and that it blows cold air

foznice Veteran

foznice

Posted
  • Author
Posted

dezz, was it cold on the day you checked it? Because it may have just been blowing outside air (which was cold)...

but yeah with mine being degassed and all.. I don't think they did it properly.. they just ripped out the canister and let all the refrigerent into the atmosphere.. the crackers didn't even bother to block off the lines.. Otherwise I wouldn't be writing this now and this thread would't exist....

Kaz200 Grand Master

Kaz200

Posted
Posted

Regent St Autoelecs or something like that are good.. in reservoir on high st near the Reservoir. They have a crappy looking workshop so you know they're good and won't rip you off! :) No seriously, very honest guys there, but the area and parking's not great so I wouldn't want to leave the car there overnight or anything.

foznice Veteran

foznice

Posted
  • Author
Posted

Thanks guys, I spoke to someone on the phone just then about it, and he said that they don't usually flush cars of my age (I can't remember what he said exactly) - for some reason..., It's not a good idea to run things through the system, he said instead just run it under vaccum for an hour or so, then regass.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...