Jump to content
SAU Community

Recommended Posts

Firstly remove the back seat.

This sounds easy in hindsight, but is hard to begin with.

1. The bottom section comes out first

seat_tab.jpg

The tab in the bottom left hand side of the pic is what is trying to be removed.

It sits about six inches in from the door, and requires a decent (re: LOT) of force backwards and upwards to get it out.

After sweat and tears (thankfully no blood) the seat lifts up, and out.

2. The back section comes out next, and needs 2 10mm bolts removed. This then also lifts out.

The parcel shelf is then removed by pulling it up to remove those little plastic annoying tabs, and pulled towards the front of the car to get around the rear windsheild wiper.

(In my case, the brake light wiring was cut, and later soldered, as it would disconect)

difference.jpg

3. The new speaker can now replace the old

In this case, JBL 60RMS 6.5" 2 ways compared to National 8w 6".

installed.jpg

otherinstall.jpg

4. Put parts back together in the reverese order to which they were pulled apart; parcel shelf, back section of seat, bottom of seat.

5. Now its done, and except for the listener, no ones the wiser;

sleeper.jpg

Sorry about pic quality i used a video camera.

Feel free to ask qs

Link to comment
https://www.sau.com.au/forums/topic/99823-r32-rear-speaker-installation-sedan/
Share on other sites

  • 1 month later...

im pretty sure the rear speaker install for an R32 coupe and sedan are the same.

well a bit easier on the sedan cos youve got back doors and makes gettin in and out easier.... thats about it

did my rear speakers myself (sedan) and helped mate do his (coupe)

  • 2 months later...

Im not sure if it is correct or not? But i have been told that there is an amp for the rear speakers? Is this true? And did you replace the speaker cable to the head unit or just replaced the speakers? Im getting a R32 sedan soon and would like some good sound. nothing over the top but i have heard the stock speakers and well they are showing there age.

If this is true is it ahrd to wire the new speakers up into the amp or just by pass it and go straight for the head unit and have fun ripping up the carpet and so forth?

  • 2 months later...

Gday Mulkers,

Just a quick question, I know it has been a while since you put ya back speakers in but do you remember where you bought them from?

Having read your DIY I’m now deciding to go with the 6.5" JBL's like you did or put in a set of 6 x 9's with some spacers.

I guess with the 6.5's you keep the stock covers, which is a bonus,

Any thoughts since you have now had em for a while?

Thanks heaps,

Regards,

Sean'O

ps: e-bay is an option i know, but i would like to hear them before i buy.

Sean'O.

I used Kenwood 3 way 6" replacements in my 4 dr last week. They are working fine now.

If u use 6"x9" speakers u lose the plastic covers and invite ppl to lok more at ur car and contemplate being but heads.

I kept the speaker covers as i dont want my car getting more attention then it allready will once it gets back from the pantshop on sunday.

And also what speakers are u guys replacing ur front ones with? WHat sizes. I havent connected the old ones as i want to know what i should go out and buy to replace the 17yr old ones.

Any ideas?

i just put some kenwood 5 1/4 inch 3 ways (or maybe they were 2 ways) in the front. i managed to fit them in the standard pod, but will be taking them out and using an MDF holder thingy (predator posted a design). they fit ok and clear everything ok, but i think lack of air-gap is giving some distortion and high volume.

  • 2 weeks later...

Hey there R32_4door_drifting,

Sorry about the late reply but i just managed to install my speakers the day before i went on a holiday.

I got back a few hours ago lol

Front speakers, well i used a pair of JBL 6 x 4's becasue a lot of ppl i had noticed installed these and they fit in flush with a few minor cuts around the edges, i'm not the best handlyman so i couldn't be stuffed installing custome encolosures for 6" splits etc.

They sound pretty damn good compared to the old crappy ones, wait till you see the old ones lol.

Ps: i ended up going with the 2-way JBL 6.5's in the back, sound AWSOME compared to the stocko's :wub:.

i'll give you the speaker code thingo's if you want to go hunting for them, but i got all my stuff through Strathfield. Beware the 6 x 4's are a speciality so you may have to wait while they order them in. All up it cost $170 (with discounts), well worth it.

6 x 4's : GTO6426e

6.5's : GTO626e

Check out this guys r32, it helped me a bit installing them..

- http://www.geocities.com/brendonmoses/gts4page22.html

Other good info that made it easy for me...

- http://www.skylinesaustralia.com/forums/in...howtopic=117576

Good luck with it all mate,

Sorry again for the late reply

Regards,

Sean'O

  • 3 weeks later...

dont bother with the stock amp, run the speakers off the head unit and leave it at that. your headunit's amp will sound a lot better than the factory amp anyway, its a tiny round POS just behind your rear wiper motor

  • 2 weeks later...

just buy a descent aftermarket 4-channel amp, one that can fit under the seat run the speakers to that then all you have to run RCA's to the head unit. much cleaner and easier in my opinion.

  • 7 years later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...