Jump to content
SAU Community

SeanR32GtSt

Members
 View Profile  See their activity

  • Posts

    226

  • Joined

  • Last visited

  • Feedback

    0%

 Content Type 

Everything posted by SeanR32GtSt

  1. SeanR32GtSt
    Reading another post I cycled through the hot and cold air temps and seen that the servo motor arm doesn’t move at all. I also noticed a white male loom connector just laying there not connected to anything. 7F16F90D-2E09-4F48-A4D2-BCFBCFCAC783.MOV
  2. SeanR32GtSt
    I didn’t think so. It was a shot in the dark.
  3. SeanR32GtSt
    So I got the car up on ramps to start cleaning the underneath of the car when I noticed that the AC unit does not have an accessory belt running it. Could this be why my car always blows hot air inside as well. 4C9F98C9-446D-4037-96B0-ED61A707346B.MOV
  4. SeanR32GtSt
    I had the similar convo with the guy in the comments of his post.
  5. SeanR32GtSt
    Browsing Instagram and saw this post from a US based company making “smart coil conversions”. What’s the point in doing this? https://thorn.industries/products/rb-smart-coil-conversion-kit
  6. SeanR32GtSt
    I agree with gtstboy. Especially with the Nistune board. It’s what I have and I got it dyno tuned couple months ago. Made 248whp and could’ve made more if not for the limit of the stock pump. Problem with finding a different turbo is going to be the exhaust housing. Nissan uses a 6 bolt outlet.
  7. SeanR32GtSt
    This all looks terrific.
  8. SeanR32GtSt
    I’m American and idk what he means by turbo outlet pipe? To me that sounds like the down pipe?!?
  9. SeanR32GtSt
    A quick update. Being swapped with school I finally had the chance to go check if my current rods are stock. They appear to be. F5795C66-7985-4F4A-B723-255FBF2A1900.MOV
  10. SeanR32GtSt
    I’ll be getting under it in a few days to check.
  11. SeanR32GtSt
    Is there anything missing from these that would need replacing like a bush inside the endlinks before attempting to install? And do they actually make a rattling noise?
  12. SeanR32GtSt
    And would obviously require an alignment after install yes? Also with my new coilovers when they come in after I install them even though I’m matching the ore existing ride height do I need a re alignment?
  13. SeanR32GtSt
    Hmm so these are for thE fronts eh? I would’ve assumed for the rears.
  14. SeanR32GtSt
    Thank you for the advice. Ya I plan to do bout 2-3km drives after each adjustment.
  15. SeanR32GtSt
    I mean what’s the use in using them though? Like performance wise?
  16. SeanR32GtSt
    I was cleaning out the boot of my r32 looking for any tools or supplies that might’ve fell into the spare tire well. I found these that the previous owner might’ve left there? Lol. Anyways don’t know what they do or are worth but I found their website and apparently they are a Canadian product.
  17. SeanR32GtSt
    Sounds fussy. I got a mate that lives bout 10km from me with access to a lift. Our game plan is to match the current coils with the new ones. Set the dampers to middle point of soft and hard. Lower the car off the lift and check the height. Then drive for a minute to check tyre rub. If not equivalent to what the car ride height was before we will lower it some more and repeat the same process.
  18. SeanR32GtSt
    Today it’s a choice between either fortune or bc coilovers ?
  19. SeanR32GtSt
    With the new ones do I just match them up to my old ones before installing?
  20. SeanR32GtSt
    I’ve contemplated running 16X9.5 in the rear and 16X8 in the front.
  21. SeanR32GtSt
    That looks good. Sits about as low as mine. My BBS wheels are 17” so it gives the more low illusion I think.
  22. SeanR32GtSt
    How low does your car sit?
  23. SeanR32GtSt
    Lol sorry mate. Here in the states we tend to be all “anti conformity “ with the rest of the world lol. But this current height does wel with our speed bumps. I don’t have to go sideways or nothing. Just go at it at no more than 10km. I’ll take another measuring pic when I get home tonight from school.
  24. SeanR32GtSt
    As it currently sits. I measured 23 inches from fender to ground.
  25. SeanR32GtSt
    This is what I got for bc racing coils. What do they mean by “extreme low”? The height in my car now is pretty damn low with what I believe are the apexi coils
×
×
  • Create New...