Jump to content
SAU Community

Recommended Posts

Im still a beginner, but im learning fast. Is there anyone else here that does it?

I dont know amny 14yr that can actualy even figure out what all the buttons mean.

I know the basics.. and im still learning.

Anyway.

Here's a low poly V8 motor i made because i was VERY bored one day.

mymotor3wz.th.jpg

A sub i made within a few mintues.

subfixed0qk.th.png

A cool skatepark.

overview2zr.th.jpg

halfpipe2lv.th.jpg

spinebox6ii.th.jpg

Last but not least, i work in progress, a Audi A4 im doing with a tutorial. It will be high poly by the time im finished with it. And also, the textures are crap, i havent botherd to UV wrap them.

meshsmoothbad27dn.th.jpg

Edited by Twitch
Link to comment
https://www.sau.com.au/forums/topic/100076-3d-modeling/
Share on other sites

  • Replies 52
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

used to do 3d modelling ages ago, but I just don't have the time and patience for nurbing these days :D My software's like outdated by a couple of years too, which dosen't help.

Trendwhores these days just mish mash some polygons in maya or 3ds and then use it in photoshop or freehand... so not a fan of that sorta 3D.

Link to comment
https://www.sau.com.au/forums/topic/100076-3d-modeling/#findComment-1826268
Share on other sites

Trendwhores these days just mish mash some polygons in maya or 3ds and then use it in photoshop or freehand... so not a fan of that sorta 3D.

HAHA, runs and hides.....

http://www.deviantart.com/view/19138768/

Link to comment
https://www.sau.com.au/forums/topic/100076-3d-modeling/#findComment-1826431
Share on other sites

Trendwhores these days just mish mash some polygons in maya or 3ds and then use it in photoshop or freehand... so not a fan of that sorta 3D.

Ahhhhh but funky... remember your a trend whore yourself with your AE86 :(

What design area you focus on anyway funky?

Yeah before I went down the path of design I've already taken I thought I might want to get into 3d but nope... Personally found it too boring & there's not much work for it either, depends what kinda 3d too.

Link to comment
https://www.sau.com.au/forums/topic/100076-3d-modeling/#findComment-1855938
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...