Jump to content
SAU Community

Recommended Posts

  • Replies 130
  • Created
  • Last Reply

Top Posters In This Topic

PERO'S33,

It is well in advance on all those front's in my opinion, come's with in built boost controller, MAP sensor etc, so they don't need to be purchased extra. Has more map points than most and is very easy to tune. Has heaps of features, rotational idle, anti-lag, launch control.

That's my 2c.

See'ya:burnout:

I SET UP THE PROTO TYPE PLUG AND PLAYS (DONE 8 P+Ps) AND HAVE BEEN THE HIGHEST WOLF SELLER ANY WHERE FOR MANY YEARS AND HAVE MANY CHAMPIONSHIP WINNING RACE

CARS WITH THEM (5 RACES WON AT WANNEROO SAT NITE). LIFE TIME WARRANTY TO. FULL PC TUNING AND HC OPTION, FULLY

UPGRADABLE TO.www.wolfems.com.au SITE NEEDS AN UPGRADE

BUT DEVELOPMENT COMES FIRST.

Well the cooler is going in right now. I went down around 1pm to see if I could get some installation pics but they hadnt started yet ;) Should be all done by the time I pick it up, has to be serviced too, hope they have enough time :D I'm going to dyno it tonight, I'll post some pics of it installed then.

Does the Wolf come with AIR TEMP sensors??????????????

I dont think it does...(Please correct me if im wrong Steve / Paul)

Looking at the Web site its doesnt mention air temp sensors....

I think its only Autronics and Motec......

I my opinion is that these two are in a league above all the rest. Both having anti lag, boost controller,etc,etc as the others do, but also have air temp sensors placed in the engine.

So instead of running static fuel maps, the Autronic and Motec adjust fueling according to air tempurate...... so your engine adjusts to hot and cold weather......

I dont think any other ECU does that in Aust(I could be wrong Though)..

Daniel

Daniel,

I think you are wrong. Although the Wolf doesn't actually come with the sensors it does support them, and I will be running them with the new turbo. It allows for air temp compensation, most people don't need them until they go for bigger horsepower.

You'd be surprised what the new plug'n'play does have, worth speaking to Steve to get the full low-down, I just know what features I've seen.

I run a MAP sensor, which comes with the Wolf, have rotational idle and with the new turbo then I'll run anti-lag.

It also has alot more map sites than the Autronic.

See'ya:burnout:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
×
×
  • Create New...