Jump to content
SAU Community

Recommended Posts

Hi guys,

I've had bigger wheels fitted for a while now (stock to 18s) and didnt think anything of it. Anyway during a highway trip I made sure I stuck to around the 110km/h speed limit but my friends who were following me were telling me I was speeding, doing 120 (double demerits), and it hit me that its because of the wheels.

Just want to know if anyone has had their speedos corrected, is this a DIY job? if not who does it in Sydney? Approx cost as well.

Thanks!

Link to comment
https://www.sau.com.au/forums/topic/101291-speedo-correction/
Share on other sites

If your tyres are the correct profile they should be the same rolling diameter as the stock tyres and therefore not affect the speedo reading.

If they are oversize I think there is an electronic kit (Jaycar?)that can vary the speed sensor output to correct the speedo.

I could be wrong.

Do a search.

Ok I did a search and picked up a few threads about it. This thread seems to sum it up.

http://www.skylinesaustralia.com/forums/in...wtopic=1461&hl=

Looks like its pretty involved for a DIY job

Has anyone got theirs corrected by a specialist in Sydney?

Maybe your friend's speedo reads over the real speed (which is the usual level of inaccuracy of speedos).

If you have fitted the correct replacement 18" tyres, then the speedo reading should not have varied significantly. Ask the tyre place to show you the manufacturer's specs on the tyres you fitted compared with the tyres you replaced.

I DIY'd in my 180SX and would be happy to help if I can.

Perhaps you could duck in to JustJap and have a look at an R33 cluster and see if it has the trim pot so you can adjust yourself.

With hindsight though, if I faced the same problem again, I would just go and buy the correct profile tyres.

Cheers dude, good luck sorting it

when i bought my nismo 300km/h speedo it was out by half eg when i was doing 60 it would show 120. i bought a digital speedo corrector from jaycar and it did the job. you have to build it yourself but i just took it to an autoelectricain, the only one who could do this as i asked around. if you want pm me and i will give you the details of the guy.

btw im in sydney also.

dave....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...