Jump to content
SAU Community

Recommended Posts

Hey Guys,

Currently in mr Stag I have a full Pioneer system.

- Carosseria Headunit

- 12 Disc Pioneer Stacker

- Kevlar Splits

- 260w Coaxials

- 1000w Pioneer Sub

- 800w monoblock amp

Now I have since aquired a sponsor. Blaupunkt. Now I have never actaully heard any of their systems. Anyone got a Blaupunkt System?

Anywho, this is the new plan.

- 2x Velocity VC650 6.5" Splits 120w RMS (Front and Rear)

- Velocity VX652 6.5" Co-axials 120w RMS (Mounted on back Pillars)

- 3x VW 1200 12" 1200w Sub (Mounted 2 facing out, 1 facing in)

- In Dash DVD player touch screen

- 2x 6.5" Headrest Monitors

- 3x Velocity Monoblock 1x400w amps

- 1x Velocity 4 channel 4x100w amp (For the splits)

hmmm....yeah thats about it. What are your thoughts?

Link to comment
https://www.sau.com.au/forums/topic/101336-my-new-audio-set-up/
Share on other sites

Blaupunkt are pretty good. They will rival most other brands out there at the moment. I would especially take it if they are a sponser and that stuff is cheap / free...

One thing tho... I wouldn't use a 400W amp on a 1200W sub... You are always best to have more power than needed when powering a sub. Otherwise you will find that the amp will either go into protect mode (when up loud) or the amp will start to distort before the sub does and will try to make the sub reproduce its lovely distored sounds and cause damage to the sub.

- Crimpage

Take a look at the true RMS figures on the sub (if they will tell you) I wouldnt be surprised if that was 1200w in good conditions for 3.5 sec. I would imagine you will be tunig the system to play below the point of distortion anyhow :O Anyhow, all this gear should sound pretty smegging good, id' love to see some photos when she's done.

Well because you will find when you go for sponsorships 9/10 times you will get a Quasi sponsorship. Heavily discounted. I am not at liberty to say how much though... Contract :( But yeah, I'm currently in negociations for a full sponsorship. They just dont hand them out to anyone though.

If you want a sponsorship, have a talk to some companies. Pitch some ideas, sell yourself :)

  • 3 weeks later...

nope, seen quite a few blaupunkt head units though, quite good... different and unique...

the information on the sub on their website says that the 380 sub (1000watt rms) has a frequency response of 25 - 1000hz, but like every other place, they dont state a price, they also dont say shit about it being either a dual magnet, dual voice coil, the strength of the magnet etc...

normally that isnt stated for a reason, so i can only assume that it is a single magnet single coil, meaning, if it is powered correctly, it will burn out the coil pretty fast...

due to lack of info, and better options out there, i wouldnt pay more then 300 for one of those, even then, i know better subs to buy...

and as for your contract, ANYONE and EVERYONE can and should get discounts on electronics... never buy the sticker price, they are rediculously priced... if they say they cant give a discount (and its not on special) ask what you have to do to get one, if they say they really cant, f**k em...

Blaupunkt are ok, they are usually more associated with head units though, but have a nice range of stuff. Its not high end, but better than some.

I can't believe they only have a 400WRMS amp (I gather its a mono amp). Thought they would have had a more powerful version, especially if they are quoting 1000WRMS for some of their subs.

The 12" VW subs that are 1200watts are probably only 400WRMS.

You won't 'burn out' a coil.... If you overpower the sub then your a good chance at it. It doesn't matter how many coils there are.

Stick with the power recommendations from the manufacturer, keep your amp gains adjusted appropriately to prevent clipping and they will work for a loooonng time.

Fixxxer

Blaupunkt are ok, they are usually more associated with head units though, but have a nice range of stuff.  Its not high end, but better than some.

I can't believe they only have a 400WRMS amp (I gather its a mono amp).  Thought they would have had a more powerful version, especially if they are quoting 1000WRMS for some of their subs.

The 12" VW subs that are 1200watts are probably only 400WRMS.

You won't 'burn out' a coil.... If you overpower the sub then your a good chance at it.  It doesn't matter how many coils there are.

Stick with the power recommendations from the manufacturer, keep your amp gains adjusted appropriately to prevent clipping and they will work for a loooonng time.

Fixxxer

Thanks for your help champ. The VW subs are 1200w rms each :huh:

C'Mon People. Someone must of heard or own a Blaupunkt sub

what would you like to know about the brand.( I sell the complete line.) also did you chat with the dealer or the manufacturer?

the screen you mention hasn't been released yet. I'm waiting on one currently.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...