Jump to content
SAU Community

Recommended Posts

I just bought an all in one split dump/frontpipe.

The all in one design allows the wastegate pipe to be much longer than the HKS style split dump and separate frontpipe combo.

This is supposed to reduce turbulence therefore improving the flow.

Some say that the all in one bellmouth type can make more power in the top end than either of the split types when running high boost but not everyone agrees with this.

Do a search and make up your own mind.

i was origianally going to go for a split style one... from marky at Exhaust technology (SA)

However he informed me that with the stock O2 sensor, they apparently have 3 prongs or somethin like that, and one of those sensors registers the heat expelled out of the turbo/wastegate.

now if your on full boost for a while (ie long hills thrash) then the air coming out of the wastegate pipe is much hotter than waht the O2 sensor (in the front pipe still) is reading.

Dont know exactly how this effects the computer etc of a stockish car..... but marky informed me to simply go for a bellmouth design.

yer the one in looking at is an all in one screamer and front pipe, so its like a normal front and dump all in one pipe but the seperate wastegate pipe doesnt join back into the exhaust. So what do you guys think ..

Hey im getting a split dump very soon, a stainless steel one that goes from turbo to front pipe.

How is the factory unit restrictive???they look very similar in the pic above apart from the SPLIT design, is it just its flow capabilities of the stock one???

And i assume youll see the same amount of gains from going front/dump combo, or just the dump pipe unit itself with an aftermarket front pipe???

is it a good idea to have the split dump heatwrapped first?and how much wrap will i need?

Edited by nsta
  • 1 month later...

i was all in on getting one of the batmbl ones but after showing my friends they all say to get the greddy split dump and blitz front pipe because suposedly where the front and dump join has alot of stress and they crack easily there with the 2 in 1 designs,

and its actually happened on my mates s15 he had a 2 in 1 design and it cracked right where the dump and front would usally joing now he has the greddy & blitz combo!

around the same price as batmbls too

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm seeing torque specs all over the place for the OUTER tie rod, but none for the INNER tie rod, where it connects to the steering rack. Even in videos, people are just tightening em up as much as they can with a wrench and that's it. Anything tightened down without torque makes me nervous. Anyone know what the spec is for it?
    • Hope you had a great time here in our tiny country.   The JDM scene we have here is quite small, it's mostly BMW, Volkswagen with burble tunes haha. But the few JDM cars we do have in the scene are pretty nice. Some of my friends drive cool s14's too. Both built engines, red one makes abt 500, blue one abt 400 i think?
    • Ye good idea , would have never thought of something like that. Might aswell do it to every pulley and the balancer while I’m there 
    • Use an LS1 or similar, via kit like Frenchy's. But.... It's probably not the alternator. It sounds like belt squeal, which would be because the pulleys are glazed. Rub every groove on the pulleys with 120 grit paper. Report back. Oh, and new belts afterwards too. The old new ones will be shitted up already.
    • Hello all I have 2 r34 sedans , one turbo one na, only recently aquired the na 34.  Man what is with these things.... My turbo 34 started sounding like a super charger, it was screaming at anything above 4000rpm , I took the alternator apart and replaced the front bearing which is the only one I think you can access and it did not fix the issue so presumably the bearing in the rear of the alternator is gone. ( diagnosed it was the alternator by taking off the aux belts one by one to figure out which pulley or bearing it was )  My friend gave me one he had lying around, Installed it , it did not squeal for maybe 500kms and now its started to squeal again briefly on startup  Recently got an na r34 and I replaced the timing belt, water pump + all the auxillirary belts. Runs amazing but it suddenly developed the same squeaking problem but significantly worse, Ive had my neighbour come down screaming at me because it was waking her up everytime I moved the car. It takes a good 2 minutes before it quietens down.  Im yet to diagnose where its coming from but im fairly sure its coming from the alternator aswell. My question isnt about how to fix it but rather where can you get a new alternator for an rb25 neo??? Ive searched everywhere but I havent been able to find a direct fit oem type replacement thats not genuine. All the automotive stores sell an oex one - BXA035 - which I picked up for cheap through a friend with staff discount , got it home only to find the connector is completelty different.... As far as im aware bxa035 is for rb20/30's and after a bit of figuring out the bxa035 has an ev14 type connector, which is tiny compared to the rb25 connector. I actually had an ev14 connector lying around which I was considering just replacing the bigger plug with to get the alternator working but the bxa035 is rated for 70amp vs the rb25 alternators are 90amp ( or so ive been told ? ) That paired along with the fact im about to install an amp + sub in the back and I have the stock sized small battery Im not sure itll do the job unless anyone has another opinion?  I know and have seen all the websites selling the ls1 alternator conversion kit but I am not going down that route, nor do I have the money to. Hopefully I can figure out how to get 2 brand new alternators for both cars. I would buy second hand which there seems to be many of but considering how common this seems to be im sure If I installed a second hand one it would start squealing in no time  Or even better if anyone knows how to fix the issue directly with the alternator itself... Any input appreciated Thank you     Link for bxa035 connector picture
×
×
  • Create New...