Jump to content
SAU Community

Recommended Posts

Buy some mesh from supercheap. Attach it. If you like it, leave it. If you don't, take it off. It only costs $20-$30 I think. I put some on my car and with the current front bar (not that one <-----------) I think it looks slightly better with the mesh.

On a side note. So pissed I didn't get a photo but I looked at my mesh at the train station on Tuesday and saw a medium sized FROG splayed across the mesh! It was hard and crusty by this time but I thought that was kinda cool.

So yeah, mesh stops frogs getting mashed into your cooler.

Edited by Dee 33
  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I went for no mesh. It's been like that since I installed the cooler, I do a lot of freeway/city driving, and the condition looks the same as it always has. You do get a few bugs, but when I wash my car I just wipe it down as well.

  • 2 weeks later...
I would say not having mesh is more for the wank factor... :rofl:

I went mesh to hide my fmic.

Its the look I want.

took long enough for someone to say it!!!

thats what ill be doing..mesh to hide the cooler as much as possible. black mesh, but only if i can find a mesh that doesnt look cheap...which most of them do

The only way to "hide" a FMIC is to paint it satin black, then put black mesh in front of it. But why "hide" it in the first place :).

I just prefer to spend $30 to replace the mesh rather than $200 to replace the fmic.

nsta

You need;

- Two different lengths of wood (thick, strong pieces). One the size of you horizontal sides (top/bottom), the other the size of your vertical sides (left/right)

- Masking tape

- Two big G-clamps

- Rubber hammer

- 3 large pop-rivits

- 3 strips of sheetmetal. Approx. 1" x 2" , with a hole (the size of the pop-rivits) drilled through the middle

- Tube of Automotive Sikaflex

- Side cutters (assuming it is aluminium mesh)

- A large table covered with some thick soft blankets (make sure the top layer is not your best blanket ;))

- Work bench

- A mate to give you an extra pair of hands

Now i am only going off memory from when i did mine 10 months ago

1/ Place bar face down on table

2/ Place mesh sheet over hole, then cut mesh to size, leaving at least a 1" overhang all round (a 2" overhang on top is better)

3/ Starting with the bottom, use the masking tap to mark the edge of the hole. Take mesh to work bench, line marked edge, on mesh, with edge of workbench, place wood on top of mesh, also at the marked edge. Use the G-clamp to firmly clamp the wood to the bench, ensuring all is still lined up. Use rubber hammer to gently hit the overhang up to a 90deg angle, thus forming the lower lip.

4/ Place mesh back on bar, position properly and cut along the overhang edge, to allow the sides to be folded.

5/ Using step 3/ as a guide, do the same thing for both sides, then the top. Always do only one fold at a time and re-measure the edge of the next overhang after every fold.

6/ Fold the excess, from the corners, over the sides, to form a "tray". I used small cable ties to prevent the flaps from sticking out. The mesh should now fit snug arround the hole.

7/ Remove the mesh, thoughly clean the inside of the bar, where the mesh makes contact to the bar. Position mesh back on bar.

8/ At the top, you should have three plactic tabs. Not sure if they have a hole in each tab already, but if they don't drill a hole in the middle, the same size as your pop-rivits.

9/ Pass the pop-rivit through the bar, then up through the mesh, then through one of your pieces of sheetmetal. Repeat for the other 2 tabs.

This is the only pic i can provide to help you ;)

post-1811-1139920097.jpg

10/ For the other sides (and along the top where possible) pump in the sikaflex, making sure it reaches the bar. Don't be shy, i used a whole tube on mine :(, just make sure it is not visable from the front. Use a "make shift" scrapper to spread the sikaflex evenly and to push it through the mesh.

If you are concerned about the strength, don't be :). When i hit the cat/possum the mesh broke along the bottom and side folds. It wasn't easy removing the old mesh and sikaflex :(

11/ Remount the indicator supports, refit the indicators.

and i think that is just about it :P

GOOD LUCK!!

Al

I had a mate that had his car fitted with a front mount along with an engine conversion and he cant get the car engineered until he covers the intercooler with mesh. apparently its a defect, but then again what isnt these days. i think just having a skyline badge is a defect to most cops, hehe.

Edited by GTS4dood

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • 2001 BE5D Subaru Legacy B4 RSK (3rd gen) EJ208 (pink injector) Twin Turbo 280PS 5-speed manual Full time 4WD "RSK" grade which means all of the above LQC option which means stock rear spoiler  I got it primarily to export to someone outside Japan who was interested. These BE5 Legacy B4 RSKs are going through a bit of a resurgence right know in Japan as they are one of the few cars from the "turbo, manual, RWD/4WD, 280hp gentleman's agreement era" cars that don't require stupid money to purchase. Which for some people might be a good opportunity to get as a base for restoration. If I can't find anyone to purchase it I will certainly be doing that myself over the long term. Why? Because it's properly fast in stock form, handles well enough for a GT sedan, there's still enough aftermarket and (if you can wait a while) genuine part support to make it a restoration candidate (<-- that will only get worse over time so it's a case of do it now or choose get a BL5 4th Gen). Mechanically it's fine, has only 89,200kms on the odometer. The problem with this car is that the body and exterior trims are weathered from at least the last 10 years being parked outdoors. I'm the 3rd owner, the first owner was the one that had it for 14 years and barely drove it, had a low-speed front impact (which didn't damage anything behind the radiator support) and got it fixed and sold it. The 2nd owner put most of the kms on it and parked it outside for the last 10 years, hence the door rubbers have seen better days but if you overlook those cosmetic details, it presents pretty nicely. There is some minor rust on the LH rear wheel arch which I'll have looked at too at some stage.  Also as you'd expect from a car this age, the clear top coat is gone, leaving a satin finish on the roof.  Mechanically it's fine (as you would expect from a car with less than 100K kms) but the steering does feel slightly vague around the centre position at higher speeds. So first on the list is to get the steering rack bushes looked at. There's also the Lock button on the remote which doesn't work, but the Open button does.... it means that the anti-theft system thinks it's always open? It seems like if you open the car and don't start the engine within 3 mins or so the anti-theft kicks in again without any beeps or signals. So if you got to start it after that, it won't. You have to push the open button again. That's how I understand it anyway. Just a small irritation but not a big problem to sort out. There's only one mod, the Wangan SPL muffler. Just a tad louder than stock. It's a really good mod for those who don't want to wake the neighbours but still want to hear a more prominent unequal length header EJ20 sound. Anyway I hope to get all those things done eventually, that is unless someone wanted to import it to their country from Japan (where I live). I'm open for negotiations as I really would like a Skyline... but this will definitely suffice in the meantime 🙂 *Disclaimer: This is how I picked it up from the dealer, minus the stuff on the back seat. I haven't cleaned the engine bay or done a thorough exterior clean, aside from spray painting the wipers. 
    • Wow, even with the Audi logo centre caps. I love OEM wheel mismatches. 
    • Welcome!  Can't go wrong with a Stag.
    • Looks good. Nice height.
    • Hey all, a little help from the Stagea hive mind plz.. I'm days away from buying either a 2002 Stagea 250tRS AR-X Four, premium leather, power seats and all the old switches etc that go with it, or a 2002 Stagea 250tRS VR-X Four AERO, pov pack, cloth seats etc, with coil overs, sports zorst, comes with original zorst and suspension and parts. (I think I've got the models right?) Both are VQ25DET, have 160000kms, both straight no rust both with $2000+ in recent servicing receipts, both ride on aftermarket 18" rims. The Aero has a replaced turbo as well. I like the cool factor of the Aero car but the AR-X has never been modified. Neither have been driven hardly at all in the last 5 years. Any thoughts on which one or does it come down to personal preference? davemoto 
×
×
  • Create New...