Jump to content
SAU Community

Recommended Posts

Hi everyone!

Today, in deep conversation about GTR performance with one of my friends the topic of thermo fans came up. I was under the impression that thermo fans were far better than using the standard radiator fans. The justification of this opinion was the fact that using the standard fan sapped a bit of power (how much KW loss I am unsure).

My question to everyone out there is; Are thermo fans a worthwhile upgrade? Or will the standard fan suffice?

Those of you who are running thermo fans I would like to hear your opinions.

Thanking everyone in advance.

  • Replies 65
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

My experience is you probably need to do a lot of extra engineering to block off all routes except through the radiator for the cooling air.

In my experience, the risk of overheating / cooking the engine is not worth the couple of extra kW you gain.

I use 2 14" davies craig thermo fans, its a tight fit. I havent made a shroud of anything for them yet but even under hard driving the temp only goes up a degree or two. On hot days stuck in traffic the temp gauge doesnt move.

My experience is you probably need to do a lot of extra engineering to block off all routes except through the radiator for the cooling air.

In my experience, the risk of overheating / cooking the engine is not worth the couple of extra kW you gain.

But in terms of efficiency, isn't the fan of minimal use when travelling faster than 60km/h?

Also, what about all the FWD cars that run electric fans from factory?

Cheers

like above, fans are used the most when sitting in traffic. They only really shine, when its 30+deg and you arnt moving.

Hell my old '79 holden used to love driving on the highway (cold temps), but go through Maccas on a hot day and it would shoot up temps :)

Thermos NEED a shroud to pull air through like the std setup, or they arnt worth much imho. Ive seen it on heaps of cars now with themos that cant keep the car cold on stop start traffic.

But in terms of efficiency, isn't the fan of minimal use when travelling faster than 60km/h?
Not arguing that. Just you need to ensure that air goes through the radiator, not out under the car. When I had a 16" DC thermo, I could get the fan to switch on on a slight uphill on the highway on a 23 C day.

The engine had seriously overheated during a track day at Winton (25 C) - within 1 lap the temp gauge was off the scale. I replaced the factory fan, and left the tell-tale light in place - 4 laps of QR (30 C) and the tell-tale lit up on the last run into the finish line.

Figured my engine wasn't worth that much risk.

Also, what about all the FWD cars that run electric fans from factory?

Cheers

That's because the engine is parallel to the radiator - the front of the engine isn't facing the radiator for a mechanical fan to work!!
That's because the engine is parallel to the radiator - the front of the engine isn't facing the radiator for a mechanical fan to work!!

Sorry, I wasn't clear with that one...

what I was getting at was, if the rad fans are shrouded correctly, elect thermos are surely as effective as mech ones...?

I have used a single 16 inch davies craig fan on the GTR. Unfortunately they draw an enourmous amount of current so you must rig them up to a thermo switch otherwise you lose the power benifit if they are on all the time. They also work within the factory shroud and reduce rotational mass to boot.

So how much is it to have a new shroud made up for the twins.Or any of the thermo fans??

The car wont overheat.If anything the fans should be set up right in the first place.Like having a thermo switch kick the fans on at optimal temp.

Question!

How much leeway should be taken into account when trying to get the engine to stay at a set goal temp.Like when should they start/kick in to be able to hold 76deg/c?

I run twin thermo's on an SR20DE+T. Since my GTR died, due to heat, I have been worried about temp.

Even with a hi-comp engine, running boost, in a drift car, so has seen a bit of stick, the thermo's are amazing.

When having the car tuned, the tuner was amazed he could not get the car over 80degrees. Hot days are not a problem and even sitting in traffic, I rarely see 75.

Also, they help cool the engine AFTER I turn the car off which I like.

I'm a big fan.... kehehe, I'm funny...

thermo fans are by far a better way to go.....its just that 90% of the setups i have seen people seem to hook them up incorrectly (hotwiring them ect)generally they pull 10amps a peice and north south oem applications????at a split second thought ford falcons,commodores have had them for years.....if i had another 10 minutes think i could think of quite a few more id reckon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The average previous owner for these cars were basically S-chassis owners in the US. Teenagers or teenager-adjacent. I often tell people that neglect is easier to fix than something that was actively "repaired" by previous owners.
    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
×
×
  • Create New...